| FAQ |
| Members List |
| Social Groups |
| Calendar |
| Search |
| Today's Posts |
|
#1
01-01-2012, 11:48 AM
|
|||
|
|||
389 piston in a 62 4cyl
I found a set (8) of .030 over cast 389 pistons. I have read on here about using them in the 4cyl, but will they increase the compression to much for a daily driver ?
and I picked up another engine that is a '61. It does not have an oil filter, It just the part that bolts to the block in place of the filter adapter with the pressure sending unit. Is this common for '61s ? Thanks |
|
#2
01-01-2012, 01:53 PM
|
||||
|
||||
|
Are the pistons flat tops or dished?? Flat tops, compression will be in the 10.25 range, dished will be 8.6 range.
An oil filter was an option. They used a bypass plate instead. Dont see the bypass plate too often.
__________________
Keith Collier 61-63 Pontiac Tempest Tech advisor POCI.org |
|
#3
01-01-2012, 03:37 PM
|
|||
|
|||
|
the pistons are flat top. the ones I took out are dished
Last edited by OldS-man; 01-01-2012 at 03:38 PM. Reason: add the ones i took out |
|
#4
01-01-2012, 03:46 PM
|
||||
|
||||
|
You can use them but will need a different head to bring the compression down.
__________________
Keith Collier 61-63 Pontiac Tempest Tech advisor POCI.org |
|
#5
01-01-2012, 06:49 PM
|
|||
|
|||
|
Thanks Keith, your info really helps me out.
is there a piston I can buy and use the head that I have. I didn't purchase the 389 pistons yet . |
|
#6
01-01-2012, 07:02 PM
|
||||
|
||||
|
Back in 1999 I purchased low compression pistons from Kanter's for my 1961 4 cylinder motor. Turns out they were the 10.25 to 1 pistons. http://www.kanter.com///productdetai...Cat=32&Prc=362
Make sure they are the low compression ones. Don
__________________
 1966 GTO 1966 421-10.1-1 comp-Race Tec 23cc Pistons KRE Tri-Power KRE 65cc Aluminum Heads XE274 cam by Comp Cams DUR 230 Int 236 Exh @.050 - 110 LSA LIFT .491" Int .491" Exh Tri-Y-Headers by Tribal Tubes w/ Goerlich Mufflers 1966 Muncie Wide Ratio 4-Speed 1968-72 Chevy 12 Bolt Rear End w/ 3.73 rear gears Last edited by SD421; 01-01-2012 at 07:05 PM. Reason: grammar |
|
#7
01-01-2012, 07:10 PM
|
||||
|
||||
|
Any decent machine shop should be able to get pistons for you. I got my last set from NAPA. .030 over 389 pistons were about $20 each. Was not building a performance engine so went with a stock replacement cast piston.
__________________
Keith Collier 61-63 Pontiac Tempest Tech advisor POCI.org |
|
#8
01-01-2012, 08:27 PM
|
||||
|
||||
|
Just open up the chambers a bit on the spark plug side of head, no real cost. It will be under 10:1 stock if the head hasnt been milled alot. 10.25:1 engines adverstised are usually more like 9.75:1 actual. Will 5-8 cc removed , target an 78-80 cc chamber
__________________
63 Catalina coupe 467 cid budget drag car low 11's 1/4 , 7.0's 1/8th pump gas n/a 66 Star Chief Executive 59k mile 389 67 IH Scout project 2WD "Indian Scout" 69 Le Mans 2 dr HT 350 91k mile 15 sec 1/4 69 Firebird 400 Burgandy/Black 70 Olds Rallye 350 F85 4 speed 3.91's 70 Olds Cutlass Cruiser Red Wagon 350 108k miles 15 sec 1/4 12 sec w 455 74 Cheyenne Super C10 LWB Gen 6 454 w ZZ502 cam 3.07gear 13.1 1/4, 8.3 1/8 2020 RAM 1500 SLT 4x4 5.7 A8 Hemi 2008 Saab 9-3 2.0T convertible |
|
#9
01-04-2012, 11:20 PM
|
|||
|
|||
|
i just checked with Kanter. Rings,rod,main,cam bearings.Gaskets,oil pump,chain and gears.DISHED pistons,intake and exhaust valves. Valve springs,lifters,valve guides.Push rods,rocker arm kit.
$850. plus $126 to re-grind my cam. probably going this way. |
| Reply |
|
|
The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.
Linear Mode
