| FAQ |
| Members List |
| Social Groups |
| Calendar |
| Search |
| Today's Posts |
|
#1
01-19-2014, 11:04 PM
|
||||
|
||||
421 Piston Recommendations
Hi all, Time to get pistons for the original WG 421 for my 1965 2+2. Planned build will be .060 overbore (necessary) aftermarket forged rods, moly rings, original 76 casting heads, Ram air IV cam, Rhodes lifters, Tripower and H.O. exhaust manifolds. I do not have a ton of $$$ for this motor so no custom units for me. Should I go cast? forged? any recommendations for a manufacturer? The last one I built had a set from Warrior racing and I do not think they are in business any longer. any suggestions would be helpful. Thanks in advance!
__________________
1965 2+2 1966 Catalina Convert 1968 Firebird 350 1969 GTO 1967 Bonneville 4 Dr Brougham 428 1967 Bonneville 2 dr 1959 Buick LeSabre 2dr |
|
#2
01-19-2014, 11:12 PM
|
||||
|
||||
|
|
| The Following 2 Users Say Thank You to b-man For This Useful Post: | ||
|
#3
01-26-2014, 12:22 PM
|
|||
|
|||
|
My two cents, going .060 over will create more heat.
|
|
#4
01-26-2014, 03:23 PM
|
|||
|
|||
|
If you're gonna beat on it Forged pistons are a must. A good balance Job is a must also
__________________
so many pontiacs, so little time.................. moderator is a glorified word for an unappreciated prick.................. "Only two things are infinite, the universe and human stupidity, and I'm not sure about the former." --Albert Einstein "There is no such thing as a good tax." "We contend that for a nation to tax itself into prosperity is like a man standing in a bucket and trying to lift himself up by the handle." - Winston Churchill |
|
#5
01-26-2014, 06:04 PM
|
||||
|
||||
|
I'm running BRC forged in the Catalina.
Jim
__________________
65 Catalina sedan. Allen Thomas Performance 495. KRE Heads at 310cfm ported by SD Performance, ProSystems Dominator carb on ported Victor intake, P-Dude custom grind hydraulic roller, MSD ignition, 3.50 Moser/Ford rear. F-Glass front bumper by son Rob, rear by the old man and joint effort for trunk lid. 3950# w/driver. Best of 9.5761/139 on 175 shot, 6.01 /114 in 1/8. |
|
#6
01-26-2014, 08:04 PM
|
||||
|
||||
|
8 lug, I dont have a choice on .060. I know the heat build up will be a problem but I really want to use the original block. I will not be drag racing but will be thumping around on the street. being a manual trans car, it will see lots of RPM swings.
__________________
1965 2+2 1966 Catalina Convert 1968 Firebird 350 1969 GTO 1967 Bonneville 4 Dr Brougham 428 1967 Bonneville 2 dr 1959 Buick LeSabre 2dr |
|
#7
01-26-2014, 10:45 PM
|
||||
|
||||
|
.060 is not a problem in these early motors. Won't run noticably warmer.
__________________
 Mike McCarty You can drop the line, but you'll never kill the spirit!Pump gas 535 w/Marcella cv/1's. 11.0 compression, 4000 stall, 3.73 gears, 275 radial, to the axle exhaust, 3470# w/driver. 9.49 @ 140..........so far |
|
#8
01-27-2014, 11:30 AM
|
|||
|
|||
|
As with Jim above, I am also running BRC Forged pistons in my 63 - 421 bored 30 over (~428).
BRC has a very good tech dept should you have any questions. (386)364-5623 However, I did not purchase them directly through BRC,. Mine were purchased through Ken at Ken's Machine Shop 512 S. Main Street Brooksville, FL 34601 Phone (352) 796-8800 Email: pontiacdude@outlook.com http://www.angelfire.com/fl4/pontiacdude428/ Ken helped in determining the correct dish-out which enabled me to run on pump gas ~ 9.8 compression ratio. |
|
#9
01-27-2014, 12:51 PM
|
||||
|
||||
|
Did the block already go +030?
If you could sneak by at 4.125 that gives you a lot of ring choices. The +.005 Race Tec is a sweet piece. |
|
#10
01-27-2014, 02:31 PM
|
||||
|
||||
|
Assume all thread watchers have seen the build in HPP -- very cool, and much along these lines. Really put a hurt on the dyno!!!
|
| Reply |
|
|
The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.
Linear Mode
