FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#1
|
|||
|
|||
64 GTO Tail Pipe Question
Exhaust system from Inline Tube...
Something doesn't look right with the Tail Pipes. Like they're hanging too low. Are they supposed to be visible from the side, below lower quarter? [url=https://flic.kr/p/Vh9qxz]
__________________
John '68 Firebird Ram Air 4-spd Conv. John 14:6 Semper Fi |
#2
|
|||
|
|||
__________________
John '68 Firebird Ram Air 4-spd Conv. John 14:6 Semper Fi |
#3
|
||||
|
||||
That looks too low to me. I would say the tips should only be slightly exposed under the bumper - and should go back a little further too.
If I recall - the shop manual shows those measurement specs, but I haven't read my 64 shop manual for a while. Sure is a nice '64!
__________________
'71 Formula 455 HO Ram Air - Future Project '64 GTO 389 4bbl 4-Spd. - Nice Driver '71 Lemans Sport Conv. Modified-350/350 3.23 Posi - Driver/Project |
#4
|
||||
|
||||
Here's how I did the ones on my wife's '64. Note that they are visible below the bumper, but only about an inch or so.
The tailpipes also had the ends cut as they are on my wife's car so the ends are roughly parallel with the ground. I copied that off my original '64 tailpipe ends I still have.
__________________
BONESTOCK GOATS '64 GTO Tripower Hardtop (Wife's Car) '64 GTO Tripower Post Coupe (My Car) '99 Bonneville SE Sedan |
#5
|
|||
|
|||
From The Nov.-Dec. 1963 Pontiac Service Craftsman News
A "mile" off . . .
|
#6
|
||||
|
||||
Looks to me like the pipe is too low in the hanger. I think you need to swap sides and flip the hanger up side down from the way it's installed.
__________________
"I know just enough to keep me here, but not enough to get me out" |
#7
|
||||
|
||||
Bends on the pipes over the axle look all wrong.
To me anyway. But I had splitters and the splitters were farther forward vs the pass car type dumps next to the rear bumper. Tom V.
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
#8
|
|||
|
|||
Hmm....
Could it be that Inline Tube doesn't quite replicate original form on Tail Pipes? Guess I should have spent $1k + for a Gardner system huh?
__________________
John '68 Firebird Ram Air 4-spd Conv. John 14:6 Semper Fi |
#9
|
|||
|
|||
Here's a ref. pix of the Tail Pipe from one on EBAY...
[url=https://flic.kr/p/Viv6oK]64 GTO TailPipe_LH_REF
__________________
John '68 Firebird Ram Air 4-spd Conv. John 14:6 Semper Fi |
#10
|
|||
|
|||
Anyone have a readable instruction sheet showing dimensions for cutting Tail Pipe and installing splitters?
Accessory installation sheet? (image from Restoration Guide not very good quality). Obviously, we need to resolve this low tailpipe issue before installing the Splitters. Appreciate all of the great feedback!
__________________
John '68 Firebird Ram Air 4-spd Conv. John 14:6 Semper Fi |
#11
|
||||
|
||||
Bought a decent original driver quality set for my car.
I used this as an external guide. Got my Hangers from Ames.
__________________
'71 Formula 455 HO Ram Air - Future Project '64 GTO 389 4bbl 4-Spd. - Nice Driver '71 Lemans Sport Conv. Modified-350/350 3.23 Posi - Driver/Project |
#12
|
||||
|
||||
I think the splitters take a different hanger in the back don't they?
__________________
"I know just enough to keep me here, but not enough to get me out" |
#13
|
||||
|
||||
Yes.
__________________
'71 Formula 455 HO Ram Air - Future Project '64 GTO 389 4bbl 4-Spd. - Nice Driver '71 Lemans Sport Conv. Modified-350/350 3.23 Posi - Driver/Project |
#14
|
||||
|
||||
__________________
'71 Formula 455 HO Ram Air - Future Project '64 GTO 389 4bbl 4-Spd. - Nice Driver '71 Lemans Sport Conv. Modified-350/350 3.23 Posi - Driver/Project |
Reply |
|
|