FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#361
|
||||
|
||||
Wow $345 for gasket style windshield and over $950 for glue in style.
|
#362
|
||||
|
||||
Wow $345 for gasket style windshield and over $950 glue in style.
|
#363
|
|||
|
|||
ouch!
Was that quote from VINTAGE GLASS?
|
#364
|
|||
|
|||
That extra 1/2" - 3/4" all the way around is costly.
|
#365
|
|||
|
|||
Ashtray bulb holder
Quote:
Also, does anyone have the small bracket that attaches the light bulb to the top of the ashtray (also for '63 - maybe all the same)?
__________________
Hoping to finish a project while I'm still able to push the clutch in.... 1963 Tempest Convertible (195-1bbl, 3-speed transaxle. 428 RAIV, 5-speed, IRS planned) Pictures |
#366
|
||||
|
||||
Apparently no one makes the larger windshield. So $ 995 is an nos one. Yes that was from Vintage glass.
|
#367
|
||||
|
||||
Windshield
Contact all the large glass company’s. They may have some setting in inventory. And cheaper than $900+.
|
#368
|
||||
|
||||
Convertible windshield trim
Looking for a right side top corner. Jim
|
#369
|
||||
|
||||
Stainless trim for a gasket style windshield. 63 Sport coupe.
|
#370
|
|||
|
|||
Need this trim piece for a 63 Lemans
|
#371
|
|||
|
|||
Wanted - '63 Front License Plate Bracket
Does the '63 use a bracket to mount the front license plate? The previous owner of my car just had the plate attached to the upper two screws of the valence, but since there are also lower screws that are spaced closer together, I'm assuming there should be a bracket to mount it properly.
Just found this picture - looks like the bracket just attaches to the lower holes. I can probably make something to work, but would prefer a correct piece if possible.
__________________
Hoping to finish a project while I'm still able to push the clutch in.... 1963 Tempest Convertible (195-1bbl, 3-speed transaxle. 428 RAIV, 5-speed, IRS planned) Pictures Last edited by tekuhn; 03-20-2021 at 11:57 PM. |
#372
|
||||
|
||||
The bracket, besides holding the plate, also moves the bottom of the plate forward so its straight up & down. Instead of slanting back at the bottom.
__________________
Keith Collier 61-63 Pontiac Tempest Tech advisor POCI.org |
#373
|
|||
|
|||
I have always wondered the same thing. If someone has one of these we can most likely copy and fabricate something pretty close.
|
#374
|
|||
|
|||
Am seeing this on ebay this morning, it looks a lot like the bracket in the photo. Something like this may be close enough to work
https://www.ebay.com/i/200717142322?ul_noapp=true |
#375
|
|||
|
|||
Most likely that InlineTube bracket could be modified to work, but might be just as easy to start with a piece of flat steel or aluminum stock and bend my own. It basically needs to look like this from above with an angle bent into the inner straight piece to match the curvature of the valance.
__________________
Hoping to finish a project while I'm still able to push the clutch in.... 1963 Tempest Convertible (195-1bbl, 3-speed transaxle. 428 RAIV, 5-speed, IRS planned) Pictures |
#376
|
|||
|
|||
manual transmission carb
Quote:
How much did you want for the carb? Is it ready to bolt on or needing rebuilt? The one on my car is not original and is in need of a new base & rebuild. Thanks, Mark |
#377
|
|||
|
|||
Sorry looking for a 2 barrel carb for a manual transmission V8 car..
I didn't take the time to read over the entire posting. Last edited by MBLemans; 04-11-2021 at 09:34 AM. |
#378
|
|||
|
|||
63 Lemans tail lamp bezel and fuel door.
Just took my tail lamp bezels and fuel door for re-chroming and was quoted $2000 because of how pitted they are. Looking for ones that are in half decent shape to be chromed.
|
#379
|
|||
|
|||
Did you see my ad?I have a complete set that wont need to be rechromed except MAYBE the fuel door.Tom
|
#380
|
|||
|
|||
I am looking for a 63 4bbl 4 cylinder air cleaner, front bumper, driver mirror, turn signal stalk, and distributor. Trying to revive this bronze beauty. Please help a lemans newbie out!
|
Reply |
|
|