[JUDGGTO69]

Looking for a needle in a haystack...what have you?

[jhein]

I know everyone will tell me not to hold my breath, and I get it, these have been on backorder for a very long time. But, I talked to the guy at RARE two days ago and he said he was very confident that they will have them in about 6 weeks. They have 300 left side on the shelf and are waiting on the right side. I have a set on order. We'll see.

[tom s]

I talked to Paul also,seemed like he wont be ready to ship till closer to September?He should have the casting to get machined in 6 weeks or so.Tom

[jhein]

Originally Posted by tom s

I talked to Paul also,seemed like he wont be ready to ship till closer to September?He should have the casting to get machined in 6 weeks or so.Tom

That's different than what he told me. But, whatever, they'll be ready when they're ready. At least it sounds like it could be soon. LOL.

[tom s]

Will take awhile to machine 300 iron exhaust manifolds!

[form74]

Here’s a used set on Facebook

https://m.facebook.com/groups/261362...9284401937393/

[eaglesan13]

He had 300 D port manifolds, or 300 or round port?

Originally Posted by jhein

I know everyone will tell me not to hold my breath, and I get it, these have been on backorder for a very long time. But, I talked to the guy at RARE two days ago and he said he was very confident that they will have them in about 6 weeks. They have 300 left side on the shelf and are waiting on the right side. I have a set on order. We'll see.

[jhein]

Originally Posted by eaglesan13

He had 300 D port manifolds, or 300 or round port?

D port 2.5 inch, was what I understood.

[eaglesan13]

Thanks

Originally Posted by jhein

D port 2.5 inch, was what I understood.

[JUDGGTO69]

bump

[JUDGGTO69]

bump

[4dblnkldude]

Come on Paul get these done!! I'm waiting on a round and a d port set for second gens!!

[JUDGGTO69]

bump.... anyone heard anything?

[JUDGGTO69]

Anyone heard any updates ???

[ramairformula74]

Don’t hold your breath. I was told in Sept. 22 that they would be ready Jan 23. I called in Feb and was told April. I got on the list around #245. I talked to an engine builder who also had the same delayed info but from earlier in 22. I heard also that the foundry wants atleast 1000 orders to begin production. So take this for what it’s worth, I sourced another set to get my engine off the build moving towards completion. Sounds like we’re being stringed along.

[4dblnkldude]

I spoke to him 2 weeks ago. I got put under the impression it was gonna be soon. I've had a round port set on order since Sept of 21 and D ports on order since Sept of 22. FINGERS CROSSED!

[Formulabruce]

I got a message in last 2 days about some are in the states. They were D ports, Im not sure if stock or 2.5 though, will try to find that ad.

[mysticmissle]

they are cast in china now? not surprised just thought they were cast in the states?

[4dblnkldude]

So what gives here? Theres an Ebay listing in Prescott Arizona for second gen round ports? Pont5681 I think was his handle. And it says he still had 5 more available? Now on Pauls website it says the D ports are here? I was supposed to get a phone call when they were ready, he told me that over and over. Did he sell them for more profit? I would not have minded an increase of course. I wanted to give my money to him. Not so sure now. I'm gonna call him tomorrow.

[4dblnkldude]

I received a set of round ports today. They are RARE's. I sent the money to Arizona but were shipped from Illinois where RARE is located. I don't know whats going on but I now only need a set of D ports.