[simsb52]

I have a standard length ready to ship ... $275 to your door in the lower 48. Sorry about the oil pump drive shafts.......I need a batch of 10 to break even.

Scott

[Rusty4cyl]

Scott, How much for 10 oil pump drive shafts. Thanks Rusty

[t money]

If you are looking to get 10 orders I will start off with a pre order of 2 if you can hold to the orig price of 25 plus shipping. Will pay in advance if it help to make it happen. Will others step up?

[BB70]

I'm in for one.

[janderson]

Add me in for 2.

[Robert Williams]

I'll take 4 of the driveshafts..

[JC455]

I'm down for 1 drive shaft.

[simsb52]

Ok I,ll make some..will be after the first of the year

I have a standard length ready to ship

Thanks...Scott

[Robsinno]

Scott, been trying to contact you about purchasing a retainer /timing chain setup. No luck with the phone # or email address posted on this forum. Please respond to [email protected]. Thanks

[Robsinno]

Can someone please help me get in touch with Sims Performance Machining? I've called the number (812-579-9815) posted in this forum and get "mailbox is not setup for voicemail" message. Sent message to email address ([email protected]); it was returned non-deliverable. Thanks

[rjpaige3]

Found this on another forum with a different email address; 4 year old post, though. Good luck and let me know if he answers, I'm going to need a chain/plate/bearing, too.

Scott Sims
Sims Performance Machining
P.O. Box 184
Elizabethtown, Indiana
47232
ph/fax 812-579-9815
[email protected]

[Robsinno]

Thanks RJ, I sent an email to the GMAIL address. Let you know if I hear anything.

[vidguy]

Hope Scott is OK and still supplying these. I've been running one in my Daily Driver 455 for 5 years 16,000ish miles now..
Would use one again. Shoulda bought 2!

[rohrt]

What is the deal with the oil pump drive shafts? Something special about them?

[2manyponchos]

Scott's good! I gave him a heads up there were people on PY looking for him. He called back asking how in the hell to get on the forums, so apparently he hasn't been on for a while (max performance name change). Folks should hear from him soon. -Doug

[potentpontiac]

Hey there Scott. I will need a Modified cam gear and Chain 6 thou smaller. If you can accommodate me that would be Great.
Thanks, Mike Voycey.

[Robsinno]

Originally Posted by rjpaige3

Found this on another forum with a different email address; 4 year old post, though. Good luck and let me know if he answers, I'm going to need a chain/plate/bearing, too.

Scott Sims
Sims Performance Machining
P.O. Box 184
Elizabethtown, Indiana
47232
ph/fax 812-579-9815
[email protected]

Thanks for the hookup RJ; I was finally able to get in touch with Scott using the email address ([email protected]) you found. He is still in business and making the thrust/retaining plate setup.

[simsb52]

Hi All....I am still here...still making them....the POS 9815 number works on and off...try my cell if you cant get thru..

8123508637

thanks...Scott

oh...PS...thanks Doug and Aaron!

[Aaron Quinton]

Good to see you're back man!

Originally Posted by simsb52

Hi All....I am still here...still making them....the POS 9815 number works on and off...try my cell if you cant get thru..

8123508637

thanks...Scott

oh...PS...thanks Doug and Aaron!

[vidguy]

Ditto! Good to see ya back.