[Stan Weiss]

Originally Posted by 67'7F6'Bird

https://www.facebook.com/groups/2200...63600721139660

How about posting it here also for those of us that are not on Facebook?

Stan

[Dragncar]

Originally Posted by Stan Weiss

How about posting it here also for those of us that are not on Facebook?

Stan

I am not on snoopbook either. But I do not think its possible. There are over 1,800 members of that group and the thread is 5+ years old.
10 new posts today.
It would be great if all that was on the largest Pontiac site there is, PY.
Looks like PZ is gone, kaput.

[67'7F6'Bird]

The RAVEN is Running again!!!
The DCI Ram Air V Heads were sent to John Marcella for some repair work. John added material between the valves as we noticed some slight hiarline cracks on two chambers, the area was likely opened up to much with unnecessary porting.
John reshaped the Intake ports also and installed the moldstar 90 seats. We assembeled the head Thursday night; including installing the wire on the flat surface of the head, this was already done we had the heads resurfcaed .05 then needed deeper receiver grooves installed. Next we thoroughly cleaned the heads and instlled the shaft rocker system, then valves, springs, retainers & locks. Once assembled Ed checked all Seat Pressure to 340lbs and all where within a few pounds of one another. Friday, we started by cleaning out the cylinders and top of block, got the head gaskets ready and installed the heads. We then installed pushrods and Shaft Rockers and turnig motor over setting lash to .014 thousandths cold, both intake and exhaust. Got the rest of the top end on and installed the transmission. Saturnday went thru all the wireing and then finally got her running. Today was more maintenance stuff and clean-up.

[Dragncar]

Sweet, good luck with the rest of the season.

[67'7F6'Bird]

The RAVEN is in the Trailer and the countdown begins.
See you soon!!!

[67'7F6'Bird]

Reply Below.

[johnta1]

Will you be entering the Frantic Four?


ET 6.xx
MPH 2xx.xx

[67'7F6'Bird]

https://m.me/ch/AbZlyDhlLRQ9CzFq/

[Jack Gifford]

Link doesn't work...?

Best of luck to the Raven and crew!

Now i'll regret not getting to Norwalk this year.

[67'7F6'Bird]

https://m.me/ch/AbZDLepKgCQCsKW3/

[67'7F6'Bird]

The RAVEN ran it's best ET to date and MPH is close to 7mph higher than its previous best. Should be able to get the ET lower this weekend.

Great job Ed Page and Crew!

RIGHT LANE CAR #722
CAR WEIGHT 3,650lbs

Chassis Designed and Fabricated by Michael Hall.
https://www.facebook.com/RacecarsByHalls

Cylinder Heads are DCI Ram Air V's by Don Johnston.
http://www.dcimotorsports.com/.../dc...ir-five-heads/

RAVEN RACING GROUP
https://www.facebook.com/groups/220092308823847

[Dragncar]

7 MPH is quite a bit.
Nice job, must have felt good getting it done after hurting the motor..
How much more HP does 7 MPH equate too ?

[67'7F6'Bird]

Newest and Latest BEST.

[BILL BOWMAN1]

Originally Posted by Dragncar

7 MPH is quite a bit.
Nice job, must have felt good getting it done after hurting the motor..
How much more HP does 7 MPH equate too ?

No expert, but think about 10-12 hp to run 1 mph faster.

[67'7F6'Bird]

Breaking News!!! New Best MPH!!!

[Tom Vaught]

Congrats on your new best pass MPH.

Tom V.

[wrench]

Awesome!

[Stan Weiss]

Vice nice progress

I know you want to get it down the track. But you need to get more aggressive down low and improve that lazy 60 foot time.

Stan

[Tom Vaught]

I was told that all racing was 1/8th mile racing this year.
(also that Cooper had damaged his car in a previous race.)

194 mph is a pretty good 1/8th mile pass for that "lazy" 60 ft number, Stan.

Tom V.

[67'7F6'Bird]

Originally Posted by Tom Vaught

I was told that all racing was 1/8th mile racing this year.
(also that Cooper had damaged his car in a previous race.)

194 mph is a pretty good 1/8th mile pass for that "lazy" 60 ft number, Stan.

Tom V.

We only ran 1/4 Mile. The Frantic 4 was 1/8th mile.

We did not run Frantic 4.