FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#1
|
||||
|
||||
Lunati bracket master 292 for mild 455
Hi I have a reasonably stock 455. I just picked up a st of 6x 4 heads to replace my big chamber 4x heads (unported). I typically run 14.2s with the stock 3.08 gears in my 68 lemans. Im running a stock cam as well. I have a lunati bracket master 2 cam on the shelf. Its 292/292, 230 @ .050, and 490 lift. Im just tring to pick up a little et, and gain a rougher idle. On the same token, I dont want to over cam it? If its too much cam, I might just bolt on the 6x heads with some roller rockers, and gain some compression. Any opinions greatly appreciated.
Btw i also have a performer, a performer rpm intakes, and 2200 stall converter.
__________________
1968 pontiac lemans 400. 13.16@102/8.5:1 /6x-4/lunati bm 2 cam/ 3500 stall/3.55 gears. |
#2
|
||||
|
||||
230/230 @ .050 is low risk in you 455 goals. See 12.2 ET signature on 89 Octane. Stars, idles without fouling, sounds right, runs hard.
__________________
12.24/111.6MPH/1.76 60'/28"/3.54:1/SP-TH400/469 R96A/236-244-112LC/1050&TorkerI//3850Lbs//15MPG/89oct Sold 2003: 12.00/112MPH/1.61 60'/26"x3.31:1/10"/469 #48/245-255-110LSA/Q-Jet-Torker/3650Lbs//18MPG 94oct Sold 1994: 11.00/123MPH/1.50 60'/29.5"x4.10:1/10"/469 #48/245-255-110LSA/Dual600s-Wenzler/3250Lbs//94oct |
#3
|
||||
|
||||
awesome! The 6 x heads i picked up came with screw in studs, guideplates, good valvesprings, roller rockers. I think with the stock pistons and 6x heads i will be around 9:1 cr. way better than 8 to 1. I have been researching the bracket master for a pontiac , but couldnt find too many opinions on it.
__________________
1968 pontiac lemans 400. 13.16@102/8.5:1 /6x-4/lunati bm 2 cam/ 3500 stall/3.55 gears. |
#4
|
||||
|
||||
I run the bracket master II in my basically stock 30 over 400. Runs 12.7s in a 4000 pound lemans street car with mild converter and 3.73 gear. I shift at 5200 with stock rods and pistons. It has a nice thump at idle to. I have used it in two separate 400s and am happy with it.
__________________
1972 Pontiac LeMans Thanks to Fuelab Digital Fuel Delivery Quarter-Max Chassis and Racing Components |
#5
|
||||
|
||||
I all so run it in my car , works well .
__________________
1978 ,t/a 3660# 455 2010 / 1/8 7.86 1/4 12.40 @ 109,19 http://www.youtube.com/watch?v=6PaHbLnszS0 http://www.youtube.com/watch?v=XMxhM...eature=related 12.01@109 http://www.youtube.com/watch?v=MC-dganA2jQ 100 shot 11.78. A,ll new head cam combo 96 ported bye Mike Chell!! Comp cam yes the 284 XE. Firsthand outing of the street 7.69 1/8 12.15 109.47 hot and humid.not hooking. 1.73 60. |
#6
|
||||
|
||||
cool. Im happy to here this. I am planning on keeping the 3.08 gears.
__________________
1968 pontiac lemans 400. 13.16@102/8.5:1 /6x-4/lunati bm 2 cam/ 3500 stall/3.55 gears. |
#7
|
|||
|
|||
I ran that cam in a 400 in a 3400lb car with 3.73 gear on pump gas and ran consistent 7.70's in the 1/8 with a best of 7.67. Has a nice sounding idle and performs pretty well.
|
#8
|
||||
|
||||
what heads were u running?
__________________
1968 pontiac lemans 400. 13.16@102/8.5:1 /6x-4/lunati bm 2 cam/ 3500 stall/3.55 gears. |
#9
|
|||
|
|||
I was running 62's with a clean up on the runners and gasket match to the Fel Pro 1233 intake gasket, Performer RPM intake and a 750 Holley double pump carb.
|
Reply |
|
|