FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#1
|
||||
|
||||
Rubber stop kits fenders doors hood etc
Can anyone suggest a kit that they are happy with or have for sale
I'm looking for the rubbers that fit into the fenders to guide the hood also the rubber door bumpers and I think there is the some ones for the trunk too and whatever else I can't remember ....thanks for any suggestions
__________________
1973 Firebird Navajo Orange w/shaker,1973 400/461,1972 Intake SD CNC'd,1977 Q-Jet 800 CFM w/ Cliffs Kit,Tanks Inc PA4 255 Walbro intank pump ,-8an feed/return,RobbMc Regulator,RobbMc 40 micron filter,253 CFM 6x-8's w/H.S 1:5 Roller Rockers,SD Stump Puller H/R Cam 230/236 @.050 112 lobe separation 565/.570 lift,Crower Solid Rollers,28150 Hedman Headers,3" exhaust,full tailpipes,350 Turbo,9.5" 3200 Converter,3:42 gear,8.5 posi,C/E slide-alinks,Koni adj frt shocks,Best 12.18@110.55 Lookin for 11's |
#2
|
||||
|
||||
Metro has the HF24 for the fender to hood bumper. They also show the hood stops. Also these. Snap-In Bumper for Rear Compartment. Each - SB 69.
SB 32 Door Bumper. Made with twin retainers. I think they have alot of the pieces your after... https://metrommp.com/hardware/bumpers/door/ I would think any company that makes the door seals with have these pieces. Softseal carries a kit of everything your looking for also. https://www.soffseal.com/ss-6836 |
#3
|
||||
|
||||
Hi Charles …yes I have looked around and seen different kits …soft seal looks good ….I’m just looking for recommendations….from personal usage…
Still go those door seal to put on. Got the car back and starting assembly…staring at the Rear cause not happy with the frt sheetmetal Installed rear spoiler, car never had one ….pic is sideways for some reason…lol
__________________
1973 Firebird Navajo Orange w/shaker,1973 400/461,1972 Intake SD CNC'd,1977 Q-Jet 800 CFM w/ Cliffs Kit,Tanks Inc PA4 255 Walbro intank pump ,-8an feed/return,RobbMc Regulator,RobbMc 40 micron filter,253 CFM 6x-8's w/H.S 1:5 Roller Rockers,SD Stump Puller H/R Cam 230/236 @.050 112 lobe separation 565/.570 lift,Crower Solid Rollers,28150 Hedman Headers,3" exhaust,full tailpipes,350 Turbo,9.5" 3200 Converter,3:42 gear,8.5 posi,C/E slide-alinks,Koni adj frt shocks,Best 12.18@110.55 Lookin for 11's |
#4
|
||||
|
||||
Looks good. I like the look with the spoiler. Do you do a restoration on it?
What’s wrong with front end sheet metal? |
#5
|
||||
|
||||
Thanks ….no restoration just a clean and paint really…,interior re paint of the trim panels new carpet Just a refresh….
I stripped the car here at home to bare metal and gutted it …. The frt sheet metal has never been right the nose to hood gap is brutal….doors to rear quarter seem ok it’s the frt end Here it is ready to be picked up only thing I didn’t touch was the nose them the body shop do it Talking to a few people on some suggestions….I may start a thread in the body shop but will see
__________________
1973 Firebird Navajo Orange w/shaker,1973 400/461,1972 Intake SD CNC'd,1977 Q-Jet 800 CFM w/ Cliffs Kit,Tanks Inc PA4 255 Walbro intank pump ,-8an feed/return,RobbMc Regulator,RobbMc 40 micron filter,253 CFM 6x-8's w/H.S 1:5 Roller Rockers,SD Stump Puller H/R Cam 230/236 @.050 112 lobe separation 565/.570 lift,Crower Solid Rollers,28150 Hedman Headers,3" exhaust,full tailpipes,350 Turbo,9.5" 3200 Converter,3:42 gear,8.5 posi,C/E slide-alinks,Koni adj frt shocks,Best 12.18@110.55 Lookin for 11's Last edited by cnc; 07-11-2021 at 01:25 PM. |
#6
|
||||
|
||||
Ya that looks way out. Should have it put on an alignment rack see what is going on.. There are 2 alignment pin holes that go from the frame to the body. I wonder how they are lined up.. Just some thoughts. I guess worst case scenario is get some to extend hood on the one side. Something is out of wack.
Do you have a body manual from that year that shows all the frame and body measurements? |
#7
|
||||
|
||||
That pic is with all the metal loose lol……but is still NFG….I have to go look in my books for a manual but I don’t think I do…I do have a sheet for measuments….
__________________
1973 Firebird Navajo Orange w/shaker,1973 400/461,1972 Intake SD CNC'd,1977 Q-Jet 800 CFM w/ Cliffs Kit,Tanks Inc PA4 255 Walbro intank pump ,-8an feed/return,RobbMc Regulator,RobbMc 40 micron filter,253 CFM 6x-8's w/H.S 1:5 Roller Rockers,SD Stump Puller H/R Cam 230/236 @.050 112 lobe separation 565/.570 lift,Crower Solid Rollers,28150 Hedman Headers,3" exhaust,full tailpipes,350 Turbo,9.5" 3200 Converter,3:42 gear,8.5 posi,C/E slide-alinks,Koni adj frt shocks,Best 12.18@110.55 Lookin for 11's |
Reply |
|
|