#1  
Old 10-16-2018, 06:20 PM
Ben M.'s Avatar
Ben M. Ben M. is offline
Ultimate Warrior
 
Join Date: Jan 2004
Posts: 2,798
Default Alternator excitation...

I converted my ‘73 big car idiot light cluster to gauges some time ago. The alternator has since required the engine rev’d to 1200RPM or so to get it to start charging. Investigating why (since I’m tired of it, factory gauge cars didn’t require it) I find all sorts of threads about various car lines explaining resistor wires to limit the current or sticking a lamp on the field line to switched +12V but no real consensus on how the factory did it. Looking at the drawings for this year (and all ‘71-76 big cars) shows a brown wire from the cluster to the field of the alternator. This loses it’s switched voltage in the conversion because the rally gauge cluster doesn’t use this pin, hence the problem. The drawings also show a dashed brown and white wire to the B terminal of the ignition switch that’s only energized in RUN. This is dashed so it’s optional, doesn’t say what causes this wire to be installed but I suspect it’s for gauge cars. The question remains “is it just a wire?” or is there an internal resistor added not shown on the drawings? The factory manual is silent on this, there’s just a single reference in the alternator section of the manual for checking continuity of the ignition switch source on the field wire (lamp for gauge cars) if the car doesn’t automatically charge. I know CS130 & 144 alternators make a big deal out of having a resistor on their lamp wire but I’m unsure on the 10SI the car has on it.

So... can I just hook up switched +12V to the field wire directly or do I need to stick a 150 ohm resistor in series with it? Adding the resistor likely won’t hurt a thing, I just have to add it and wire it all in, while a straight wire is simpler. If the factory engineers felt it was important to have surely they’d have said something about it. But I also don’t want to kill the regulator in my alternator...

  #2  
Old 10-16-2018, 06:38 PM
Chief of the 60's Chief of the 60's is offline
Suspended
 
Join Date: Nov 2017
Location: On the Rez
Posts: 3,233
Default

I take it you went 1 wire? Go to 3 wire. Problem solved.

  #3  
Old 10-16-2018, 09:26 PM
Ben M.'s Avatar
Ben M. Ben M. is offline
Ultimate Warrior
 
Join Date: Jan 2004
Posts: 2,798
Default

Quote:
Originally Posted by Chief of the 60's View Post
I take it you went 1 wire? Go to 3 wire. Problem solved.
Wrong. Read the post. The field wire from the bulb is no longer connected due to swapping gauges.

  #4  
Old 10-17-2018, 09:02 AM
johnta1's Avatar
johnta1 johnta1 is offline
Ultimate Warrior
 
Join Date: Feb 2001
Location: now sunny Florida!
Posts: 21,644
Default

The field wire from the alternator isn't connected to anything?
(should be)




__________________
John Wallace - johnta1
Pontiac Power RULES !!!
www.wallaceracing.com

Winner of Top Class at Pontiac Nationals, 2004 Cordova
Winner of Quick 16 At Ames 2004 Pontiac Tripower Nats

KRE's MR-1 - 1st 5 second Pontiac block ever!


"Every man has a right to his own opinion, but no man has a right to be wrong in his facts."

"People demand freedom of speech to make up for the freedom of thought which they avoid." – Socrates
  #5  
Old 10-17-2018, 09:21 AM
Ben M.'s Avatar
Ben M. Ben M. is offline
Ultimate Warrior
 
Join Date: Jan 2004
Posts: 2,798
Default

Quote:
Originally Posted by johnta1 View Post
The field wire from the alternator isn't connected to anything?
(should be)
That is correct. When you convert the cluster from a light cluster to gauge cluster with voltmeter you lose the field wire connection inside the car. I know it’s supposed to be hooked up, the concern is if it needs to be current limited with a resistor or diode combo or if I can just run a straight wire from switched +12. The factory drawings do not indicate anything other than a wire.

  #6  
Old 10-17-2018, 09:54 AM
johnta1's Avatar
johnta1 johnta1 is offline
Ultimate Warrior
 
Join Date: Feb 2001
Location: now sunny Florida!
Posts: 21,644
Default

How is the voltmeter wired?
I'd either connect to the voltmeter or the ignition switch 'ON'.



__________________
John Wallace - johnta1
Pontiac Power RULES !!!
www.wallaceracing.com

Winner of Top Class at Pontiac Nationals, 2004 Cordova
Winner of Quick 16 At Ames 2004 Pontiac Tripower Nats

KRE's MR-1 - 1st 5 second Pontiac block ever!


"Every man has a right to his own opinion, but no man has a right to be wrong in his facts."

"People demand freedom of speech to make up for the freedom of thought which they avoid." – Socrates
  #7  
Old 10-17-2018, 08:40 PM
Ben M.'s Avatar
Ben M. Ben M. is offline
Ultimate Warrior
 
Join Date: Jan 2004
Posts: 2,798
Default

Quote:
Originally Posted by johnta1 View Post
How is the voltmeter wired?
It uses the stock +12V switch (pink wire) connection on the gauge cluster - this is a factory gauge cluster that replaced the factory idiot light cluster and the wiring on the plugs is the same.

Quote:
Originally Posted by johnta1 View Post
I'd either connect to the voltmeter or the ignition switch 'ON'.
I agree... but should it be resisted with the lamp\lamp equivalent or is a 12ga wire satisfactory enough to not let the smoke out of things?

  #8  
Old 10-18-2018, 08:35 AM
johnta1's Avatar
johnta1 johnta1 is offline
Ultimate Warrior
 
Join Date: Feb 2001
Location: now sunny Florida!
Posts: 21,644
Default

Just the wire I would say.
If you had run the field wire straight from the alternator to the power feed by the alternator, then a resistor may be necessary to give it some 'difference' in voltage to regulate?



__________________
John Wallace - johnta1
Pontiac Power RULES !!!
www.wallaceracing.com

Winner of Top Class at Pontiac Nationals, 2004 Cordova
Winner of Quick 16 At Ames 2004 Pontiac Tripower Nats

KRE's MR-1 - 1st 5 second Pontiac block ever!


"Every man has a right to his own opinion, but no man has a right to be wrong in his facts."

"People demand freedom of speech to make up for the freedom of thought which they avoid." – Socrates
  #9  
Old 10-18-2018, 07:07 PM
Ben M.'s Avatar
Ben M. Ben M. is offline
Ultimate Warrior
 
Join Date: Jan 2004
Posts: 2,798
Default

Quote:
Originally Posted by johnta1 View Post
Just the wire I would say.
If you had run the field wire straight from the alternator to the power feed by the alternator, then a resistor may be necessary to give it some 'difference' in voltage to regulate?
No, it's internally regulating. The field wire is to give the rotor proper magnetization and start charging. It can do it on its own but that requires more speed on the shaft to do so. The resistor is because you don't want to cook the wiring if the key sits in the RUN state without the engine actually running.

I checked a later model year manual and they specifically say that this wire is ONLY installed for Rally Gauges or Heated Rear glass. Instead of using an 18ga wire like on the lamp circuit, they use a 24ga wire. I checked an existing harness from a gauge car I found in my stash and yes, they do only have the brown with white wire on the gauge car and not on the idiot lamp car harness. Since the gauge of wire is considerably smaller, I'm presuming they did it for a reason. I'm going to add a 100Ω 2W resistor in series with the wire I add just because better safe than sorry. I'll also tap off of the existing field sense wire near the cluster plug rather than pull the entire harness out.

Amusing thought is that this means if you put an idiot lamp cluster in a gauges car, your alternator lamp won't ever light up... and that despite what the catalogs say, the dash harness for the 1971+ full size line is actually different between gauge and lamp cars (I already found out that the engine harness they sell is wrong for multiple years).

  #10  
Old 06-17-2024, 11:39 AM
raggedjim raggedjim is offline
Member
 
Join Date: Nov 2013
Posts: 38
Default

I know this is an old post but did the 100ohm resistor fix your problem? Where did you pull your 12v keyed from?

When I did this years ago I think I pulled from a big orange wire in the bundle but added a socketed 1895 bulb in line with the original brown wire. I ended up spray painting the bulb black because every now and then it would glow!

Rg


Last edited by raggedjim; 06-17-2024 at 12:04 PM.
  #11  
Old 06-17-2024, 12:38 PM
george kujanski's Avatar
george kujanski george kujanski is offline
Ultimate Warrior
 
Join Date: Jan 2000
Location: palatine, il. USA
Posts: 7,921
Default

The resistor is a good idea. Internally in the 10SI alt, sure the #1 terminal is used for excitation, but once the alt develops output, the #1 terminal essentially becomes the sense voltage. There may be a difference in voltages between the #1 terminal and the ign wire. There should be some resistance between #1 and the switched ign wire, ... some resistance will isolate the two points. A light bulb performs all 3 functions... excitation, isolation, and indication.

George

__________________
"...out to my ol'55, I pulled away slowly, feeling so holy, god knows i was feeling alive"....written by Tom Wait from the Eagles' Live From The Forum
The Following User Says Thank You to george kujanski For This Useful Post:
  #12  
Old 06-18-2024, 11:14 AM
Peter Serio's Avatar
Peter Serio Peter Serio is offline
Ultimate Warrior
 
Join Date: Mar 2000
Location: Columbus, OH 43209 USA
Posts: 2,673
Default Here is a simple diagram for the light bulb:

Lamp in the wire to allow the alternator to begin to charge.

In the early 1980s I converted a Chevy Van to full gauges (Volt, Fuel, Oil pressure and coolant temperature) and the way I solved this problem was to leave the "GEN" light bulb socket intact and just ty-wrap the wires underneath the dash.

It could also be done using a resistor however the light bulb was a quick, easy solution
Attached Thumbnails
Click image for larger version

Name:	10SI Delco alternator wiring diagram_with light blub_revs.gif
Views:	283
Size:	24.4 KB
ID:	635526  

__________________
Peter Serio
Owner, Precision Pontiac
  #13  
Old 11-11-2024, 09:08 PM
Squidward's Avatar
Squidward Squidward is online now
Ultimate Warrior
 
Join Date: Dec 2002
Location: Mesa, AZ
Posts: 4,396
Default

Going through a little of this now. Doing a digital gauge conversion on a 67 Firebird. I run a cs105 alt. My new digital cluster has no provision for a GEN light. I will now use the hi beam indicator bulb as my gen light, because the digital cluster has a built in hi beam indicator.

I thought about using the resistor and ditching the bulb altogether. Kinda torn.

__________________
"...ridge reamer and ring compressor? Do they have tools like that?"
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:04 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017