#1  
Old 07-14-2022, 05:29 PM
Tim Corcoran's Avatar
Tim Corcoran Tim Corcoran is offline
Ultimate Warrior
 
Join Date: Jan 2000
Location: Willow Spring, North Carolina
Posts: 4,664
Default Poly locks too long or rocker studs too long?

Poly Locks are hitting the valve covers I need a poly lock about 3/4" long does anyone make them? Or do I need to get a new set of rocker studs that are .300" shorter?

__________________
Tim Corcoran
  #2  
Old 07-14-2022, 05:46 PM
ponchonlefty ponchonlefty is offline
Member
 
Join Date: May 2022
Location: alabama
Posts: 96
Default poly locks

Quote:
Originally Posted by Tim Corcoran View Post
Poly Locks are hitting the valve covers I need a poly lock about 3/4" long does anyone make them? Or do I need to get a new set of rocker studs that are .300" shorter?
spotts performance he sells on ebay. he has some that are supposed to fit under stock covers. he also has thicker gaskets you might just need those.

The Following User Says Thank You to ponchonlefty For This Useful Post:
  #3  
Old 07-14-2022, 06:01 PM
54nomore's Avatar
54nomore 54nomore is offline
Senior Chief
 
Join Date: Dec 2013
Location: Peoria, IL.
Posts: 484
Default

How deep is your set screw in the body now?

__________________
  #4  
Old 07-14-2022, 06:26 PM
Murf Murf is offline
Ultimate Warrior
 
Join Date: Aug 2000
Location: St. Marys Ks. U.S.A.
Posts: 1,486
Default

They list the length on Summit. I had the same problem & bought some that were shorter than what I had. Don’t remember which brand, Sorry

Murf

  #5  
Old 07-14-2022, 06:38 PM
25stevem's Avatar
25stevem 25stevem is offline
Ultimate Warrior
 
Join Date: Jan 2022
Posts: 1,744
Default

First you should just use a plain nut and some washers to adjust a intake and exh valve and confirm that at max lift of each that the rocker arm heel itself does not hit the valve cover.

This way if need be you can pick up thicker gaskets along with the needed length poly locks.

The other factor between stud length and poly lock length is that you want real close to 1/2” of thread engagement between the two!

You do not want the poly lock to dangle off of only 1/4”! Worth of threads.

__________________
I do stuff for reasons.

Last edited by 25stevem; 07-14-2022 at 06:48 PM.
The Following User Says Thank You to 25stevem For This Useful Post:
  #6  
Old 07-14-2022, 06:48 PM
tom s tom s is online now
Ultimate Warrior
 
Join Date: Jan 2000
Location: long beach ca usa
Posts: 18,764
Default

What ever you find get the 5/16 thick gaskets.I know Butler sells them.Tom

The Following User Says Thank You to tom s For This Useful Post:
  #7  
Old 07-14-2022, 07:42 PM
25stevem's Avatar
25stevem 25stevem is offline
Ultimate Warrior
 
Join Date: Jan 2022
Posts: 1,744
Default

Is your center lock Allen set sticking up above the body of the poly lock when the proper adjustment is made?

__________________
I do stuff for reasons.
  #8  
Old 07-14-2022, 10:42 PM
Sun Tuned Sun Tuned is offline
Ultimate Warrior
 
Join Date: Oct 2002
Posts: 2,113
Default

Crower has em in stock.

  #9  
Old 07-14-2022, 11:10 PM
Tim Corcoran's Avatar
Tim Corcoran Tim Corcoran is offline
Ultimate Warrior
 
Join Date: Jan 2000
Location: Willow Spring, North Carolina
Posts: 4,664
Default

When adjusted the set screw is about .310" below the top of the nut. I don't think the 5/16 gaskets will get me enough clearance. If I had a lathe I would cut down all the studs about .310" and that would do it. I found some poly locks listed as short but no dimensions. I sent Paul Spotts a message from ebay asking the length of his short nuts :-). I am pretty sure the valve cover will clear the rocker arm. If I had a set of studs that were 1-5/8 long I think that would do it. I think the short poly locks and the 5/16 gaskets would do the trick.

__________________
Tim Corcoran
The Following User Says Thank You to Tim Corcoran For This Useful Post:
  #10  
Old 07-14-2022, 11:35 PM
i82much's Avatar
i82much i82much is offline
Ultimate Warrior
 
Join Date: Dec 2005
Posts: 2,786
Default

i broke a rocker stud once that was too short. freaking scary.

The Following User Says Thank You to i82much For This Useful Post:
  #11  
Old 07-15-2022, 12:22 AM
Brentco's Avatar
Brentco Brentco is offline
Senior Member
 
Join Date: Jan 2020
Location: Orange County, CA
Posts: 147
Default

I don’t think they make poly locks as short as 3/4”?

Anyway, you have to play around with both the stud height and the poly lock height. IIRC, the magic number is a minimum of five turns in on the set screw.

ARP has a bunch of different heights of each, all listed on their website. I ended up with ARP 300-8246 locks and ARP 334-7202 studs.

And if you really want to get neurotic about it you can try to find the right stud height, lock height, and also just the right thread length so that the rocker is only riding on solid metal and not the threads at all. Probably not going to matter with the strength of ARP hardware, but apparently rocker studs do snap sometimes.

__________________
1976 Trans Am Buccaneer Red
468ci, 10.5:1 CR, 87 CC RPM CNC e-heads, HR 282/288, 230/236, 561/.573 lift, Johnson Lifters & HS 1.65 Rockers
  #12  
Old 07-15-2022, 12:34 AM
OG68's Avatar
OG68 OG68 is offline
Ultimate Warrior
 
Join Date: Dec 2011
Location: Chula Vista, CA
Posts: 1,475
Default

I have the Paul Spotts poly locks and studs on my 68 #16 heads. Valve cover fits fine with the. standard gasket. Oil drippers do not however

__________________
Ed

1968 GTO (Thanks Mom)
2006 Silverado
2007 Cadillac SRX
2015 Chevy Express

The Following User Says Thank You to OG68 For This Useful Post:
  #13  
Old 07-15-2022, 02:30 AM
lust4speed's Avatar
lust4speed lust4speed is offline
Ultimate Warrior
 
Join Date: Jul 2002
Location: Yucaipa, SoCal
Posts: 8,684
Default

Quote:
Originally Posted by Sun Tuned View Post
Crower has em in stock.
These are what Sun Tuned referenced:https://www.summitracing.com/parts/cro-86050s-16. Less than a quarter inch shorter, but enough to make a difference.

I can get large roller cam setups under the '67 and later chrome valve covers. It takes these polylocks, 1.75" stem length studs, Crower stainless Rockers, and 5/16" valve cover gaskets. You can skip the thicker gaskets on initial assembly and go with stock thickness, but will find out on about the 2nd tightening after about six months you will start getting some rocker to valve cover interference.

__________________
Mick Batson
1967 original owner Tyro Blue/black top 4-speed HO GTO with all the original parts stored safely away -- 1965 2+2 survivor AC auto -- 1965 Catalina Safari Wagon in progress.
The Following User Says Thank You to lust4speed For This Useful Post:
  #14  
Old 07-15-2022, 05:28 AM
Cliff R's Avatar
Cliff R Cliff R is offline
Ultimate Warrior
 
Join Date: Nov 2000
Location: Mount Vernon, Ohio 43050
Posts: 17,972
Default

It can be challenging to get everything under stock covers but it can and will work if you have the correct components.

First you need to make sure that when set correctly you have at least five FULL turns with the locknuts. Anything less will not hold the strength of the parts.

You also have to make sure that the allen set screws are fully engaged in them.

The reason we run into so many issues these day is that many of the parts are non-standard. Heads, valve lengths, lifters, cam base circles, rocker arms, etc.

Not really a big deal you just have to take the steps to make things work. Sometimes you'll need to get longer studs or shim up the ones you have as well to get enough engagement with the locknuts. They make short ones, but I have a lathe here so can cut down the typical long varieties that show up with a lot of these aftermarket roller rocker arms.

Obtain the thick valve cover gaskets as well, I have a set here and they are listed for sale in "parts" on this Forum.

So the short version of events here is to establish correct geometry at the plunger depth you are looking for (hydraulic lifters). Obtain the correct length pushrods. Tighten down the locknuts where they are going to end up at. Make sure you have at least 5 full turns on them, see if the valve covers will fit. If you need to cut down the locknuts make sure you end up with clearance for the covers AND enough engagement with the set-screws at the same time. It's really not that complicated and once you come up with the correct length for the locknuts either cut them down or buy them.

I'll add here that even if you have a lathe they are very hard parts and difficult to cut down. I short-cut that deal by cutting them off with a high speed thin grinding wheel then facing them in the lathe afterwards. This reduces that operation to minutes........

__________________
If you can read this, thank a teacher. If you can read this in English, thank a Veteran!
https://cliffshighperformance.com/
73 Ventura, SOLD 455, 3740lbs, 11.30's at 120mph, 1977 Pontiac Q-jet, HO intake, HEI, 10" converter, 3.42 gears, DOT's, 7.20's at 96mph and still WAY under the roll bar rule. Best ET to date 7.18 at 97MPH (1/8th mile),
The Following User Says Thank You to Cliff R For This Useful Post:
  #15  
Old 07-15-2022, 07:42 AM
scott70's Avatar
scott70 scott70 is offline
Ultimate Warrior
 
Join Date: May 2002
Location: maine
Posts: 2,220
Default

Using crower Enduro rockers I had to machine down the nuts to barely clear the rocker and still had to double up the gaskets to get the valve train to clear the stock valve covers.
Attached Thumbnails
Click image for larger version

Name:	20200706_111415.jpg
Views:	122
Size:	45.8 KB
ID:	594351  

__________________
72 lemans,455 e-head, UD 255/263 solid flat,3.73 gears,,,10" 4400 converter,, 6.68 at 101.8 mph,,1.44 60 ft.2007
(cam 271/278 roller)9"CC.4.11gear 6.41 at 106.32 mph 1.42 60 ft.(2009) SOLD,SOLD
1970 GTO 455 4 speed #matching,, 3.31 posi.Stock manifolds. # 64 heads.A factory mint tuquoise ,69' judge stripe car. 8.64 @ 87.3 mph on slippery street tires.Bad 2.25 60ft.Owned since 86'
The Following User Says Thank You to scott70 For This Useful Post:
  #16  
Old 07-15-2022, 09:12 AM
Tom Vaught's Avatar
Tom Vaught Tom Vaught is offline
Boost Engineer
 
Join Date: Dec 2001
Location: The United States of America
Posts: 31,294
Default

There are so many things different on my street 455 engine vs my 389 original engine,
I just install the tall valve covers and forget about it.

Tom V.

__________________
"Engineers do stuff for reasons" Tom Vaught

Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward.
The Following User Says Thank You to Tom Vaught For This Useful Post:
  #17  
Old 07-15-2022, 09:50 AM
track73 track73 is offline
Ultimate Warrior
 
Join Date: Nov 2006
Location: Munster In
Posts: 1,504
Default

On a 7/16 -20 stud, 5 threads is 1/4". More than enough in my book .

__________________
1979 Trans Am WS-6 .030 455 zero decked
flat pistons
96 heads with SS valves
041 cam with Rhoads lifters 1.65 rockers
RPM rods
800 Cliffs Q Jet on Holley Street Dominator
ST-10 4 speed (3.42 first)
w 2.73 rear gear

__________________________________________________ _______________________________

469th TFS Korat Thailand 1968-69 F-4E Muzzle 2
  #18  
Old 07-15-2022, 04:48 PM
Tim Corcoran's Avatar
Tim Corcoran Tim Corcoran is offline
Ultimate Warrior
 
Join Date: Jan 2000
Location: Willow Spring, North Carolina
Posts: 4,664
Default

I appreciate all the replies by the number of replies it seems a lot of people have had the same problem. Yes Tom tall valve covers are an option but since this is an AC car and it has a large PB booster it's not practical for this car. The valve train geometry has been checked and proper push rods have been installed. It's a mild hyd roller with Scorpion 1.65's and lift is .600 and the valves have been adjusted with 3/4 turn preload.
Current poly locks are 1.055 tall
Current studs are 1.915
Set screws are .300 below the top of the poly lock
Poly locks are engaged 7 turns with valve adjusted (3/4 turn preload)
Top of Poly lock is .400 above top of rocker arm at the pivot point

The Crower poly locks are .875 and that reduces my interference by .180. So maybe that plus 5/16 gasket will get me the clearance I need without messing with the studs.

__________________
Tim Corcoran
The Following User Says Thank You to Tim Corcoran For This Useful Post:
  #19  
Old 07-15-2022, 04:57 PM
lust4speed's Avatar
lust4speed lust4speed is offline
Ultimate Warrior
 
Join Date: Jul 2002
Location: Yucaipa, SoCal
Posts: 8,684
Default

Scorpion rocker arms are the tallest (and fattest) of just about any rocker arm. If you keep those you might be doomed.

__________________
Mick Batson
1967 original owner Tyro Blue/black top 4-speed HO GTO with all the original parts stored safely away -- 1965 2+2 survivor AC auto -- 1965 Catalina Safari Wagon in progress.
The Following User Says Thank You to lust4speed For This Useful Post:
  #20  
Old 07-15-2022, 05:07 PM
25stevem's Avatar
25stevem 25stevem is offline
Ultimate Warrior
 
Join Date: Jan 2022
Posts: 1,744
Default

It’s the bending / leverage forces applied to the top of the stud with only 1/4” of thread engagement that needs to be taken into consideration also especially when open spring forces exceeded 380 psi .

__________________
I do stuff for reasons.
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:36 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017