FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
|
#1
|
|||
|
|||
2022 Updates
None..other than rebuilding a leaking master cylinder.
Realistic et goal for 2022 10.5/127 1.50 60ft Possible et goal for 2022 10.4's/128/129 sub 1.5 60foot best et 10.76 at 125.64 with a 1.5471 60ft with 308 gears in 2018 Late 2021 replaced trashed th 350 mainly because the car wouldn't 60 foot under 1.6 I have zero miles on the fresh trans Also aiming to get 14mpg plus with the 3.73 gears. Two carbs to run back to back trusty old 950HP and the newer unproven Pro Systems which was hampered by transmission issues but showed a higher mph. The Holley gets excellent fuel mileage, close to 18mpg with the 308 gears. I currently have a 10 inch UCC convertor installed, it should have a flash of 3800..that also has never been tested with a healthy transmission. I also still have my 3200 10 inch "JIM HAND" Continental convertor..so there may be some convertor tweaking happening this year as well. I also still have not settled on shift points for this newer engine combination. So lots to test this year with the current combination of parts..I should have plenty of track days to play and test unlike the last 2 years.
__________________
466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2 373 gears 3200 Continental Convertor best et 10.679/127.5/1.533 60ft 308 gears best et 10.76/125.64/1.5471 |
#2
|
||||
|
||||
I will be waiting for all the “ results” that you share with us ( very thankful!!!).
I hope this years testing goes your way! Man I remember when you swapped to the performer RPM, and what a huge leap in performance that was going to bring ( Andy’s car performed well with that intake). That deal didn’t go the direction you hoped for OR where we were all sure it would go, picking up a tenth or two. Does the latest trans build still have the lower gears in it? 18 MPG with that combo would be crazy! But not really, considering your build and close knit tuning. I keep wondering if your great performance numbers may have al great deal to do, with how the engine, Trans and diff are all in a perfect storm of being loaded, ( highly loaded!) to propel your car to such great performance, this is in reference to all thrums with 3.08 gear. Sure seems like the 3.73 gear would improve the performance...... Carry on!!!
__________________
1977 Black Trans Am 180 HP Auto, essentially base model T/A. I'm the original owner, purchased May 7, 1977. Shut it off Shut it off Buddy, I just shut your Prius down... |
#3
|
|||
|
|||
Quote:
__________________
466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2 373 gears 3200 Continental Convertor best et 10.679/127.5/1.533 60ft 308 gears best et 10.76/125.64/1.5471 |
#4
|
||||
|
||||
Quote:
Some times the Ponti tractor responds, other times it doesn’t! Keep it ripping!
__________________
71 GTO, 463, KRE 295 cfm heads ported by SD Performance, RPM intake, Qjet, Dougs Headers, Comp cams HR 246/252 ...11 to 1 , 3.55 cogs, 3985lbs.....day three- 11.04 at 120mph ....1.53 60', 6.98 1/8 mile |
#5
|
||||
|
||||
Good stuff thanks!
Also best wishes for 2022 |
#6
|
||||
|
||||
Good luck TA, I always enjoy your results. I think 14mpg with a Holley/373s/600hp would be an amazing feat. I think 10 would be good
__________________
Chris D 69 GTO Liberty Blue/dark blue 467, 850 Holley, T2, Edelbrock Dport 310cfm w Ram Air manifolds, HFT 245/251D .561/.594L, T400, 9" w 3.50s 3905lbs 11.59@ 114, 1.57/ 60' |
#7
|
|||
|
|||
It achieved 18mpg with the 308's so it will be interesting what it does.
__________________
466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2 373 gears 3200 Continental Convertor best et 10.679/127.5/1.533 60ft 308 gears best et 10.76/125.64/1.5471 |
The Following User Says Thank You to ta man For This Useful Post: | ||
#8
|
||||
|
||||
You'll find with carb testing that once you tune one that's dead nuts on the money for your set-up, there is NOTHING waiting for you on the time slip messing around with anything else, it would defy the laws of physics if it did..........Carburetors are metering devices, wouldn't matter if you carved one out of a block of wood, if it provided adequate cfm, seamless transition and A/F spot on across the load speed range nothing else is going to improve anything.
Same thing with distributors and bug zapping ignition systems, very little if anything waiting for you there either, provided every one tested was dialed in the same and it good working order. The torque converter is a MAJOR player in what you are doing, LOTS of variables in that equation, flash stall, load stall, torque multiplication, efficiency once past the stall speed, etc. Certainly looking forward to seeing if you can find anything there. 18mpg's is getting it done for an HP950. I suspect someones been into the metering blocks and airbleeds in the main casting or it's a winning lottery ticket! I've been off the Forum for a while, what is the "new" engine combo?.........
__________________
If you can read this, thank a teacher. If you can read this in English, thank a Veteran! https://cliffshighperformance.com/ 73 Ventura, SOLD 455, 3740lbs, 11.30's at 120mph, 1977 Pontiac Q-jet, HO intake, HEI, 10" converter, 3.42 gears, DOT's, 7.20's at 96mph and still WAY under the roll bar rule. Best ET to date 7.18 at 97MPH (1/8th mile), |
#9
|
|||
|
|||
Cliff stock 950HP..but it was barely into the primaries at cruise. I believe it's the Higher compression, efficient combustion chambers , tight convertor and mild gears that combined for the mileage.
__________________
466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2 373 gears 3200 Continental Convertor best et 10.679/127.5/1.533 60ft 308 gears best et 10.76/125.64/1.5471 |
#10
|
||||
|
||||
Man for a308 gear thats a killer sixty foot time.
Good job with your combo and I'll be listening for more results. GT |
#11
|
|||
|
|||
Quote:
I 've seen similar combos go under 1.5 for a 60 foot at the same weight. So there is a lot of potential left in the combo..so it will be interesting to see how much et was loss with the bad transmission.
__________________
466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2 373 gears 3200 Continental Convertor best et 10.679/127.5/1.533 60ft 308 gears best et 10.76/125.64/1.5471 |
#12
|
||||
|
||||
U have had some bad luck but there are good time’s ahead. I will message u about some private track rentals. Let’s go have some fun , I’m ready to try a couple things….
|
#13
|
||||
|
||||
"Cliff stock 950HP..but it was barely into the primaries at cruise. I believe it's the Higher compression, efficient combustion chambers , tight convertor and mild gears that combined for the mileage."
Absolutely. The better job you do at picking compression and cam the more efficient the engine will be at light engine load. My engine is similar and very efficient. I haven't done any fuel economy testing with this one, but my last 455 with KRE heads was going between 200-230 miles on 14 to 14.4 gallons of fuel the few times I checked it. This one will go at least that far as it sips fuel if you drive it gently.........
__________________
If you can read this, thank a teacher. If you can read this in English, thank a Veteran! https://cliffshighperformance.com/ 73 Ventura, SOLD 455, 3740lbs, 11.30's at 120mph, 1977 Pontiac Q-jet, HO intake, HEI, 10" converter, 3.42 gears, DOT's, 7.20's at 96mph and still WAY under the roll bar rule. Best ET to date 7.18 at 97MPH (1/8th mile), |
#14
|
||||
|
||||
Good stuff Ta man, looking forward to your results. I like where you have started from!
__________________
Jim Moshier 1971 Grand Prix 462ci SD Performance 6x heads 1962 Catalina 389 1968 Firebird 400-455 I haven't decided "If we ever forget that we're one nation under GOD, then we will be a nation gone under." - Ronald Reagan |
#15
|
|||
|
|||
Current engine combination
466 cu inch 10.8 to 1 compression SD ported KRE heads 314cfm at .600 79 cc Torker 2 plenum work by Derek Stewart port matched and runner work by Dave Bisschop Wilson Tapered 1 inch spacer or open 1 inch SD Performance "Old Faithful 2.0" hyd roller .400/.391 lobes 235/245 dur HS 1.65 rockers Holley 950 HP or Prosystems 1000hp carb Spectre Cowl air cleaner with 4 x 14 inch filter Dougs 1 3/4 inch headers 3 inch full exhaust with X pipe and Ultraflow mufflers 3200 Continental 10 inch or 3800? Úcc 10 inch 8.5 10 bolt Eaton posi 3.73 gears Dutchman axles
__________________
466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2 373 gears 3200 Continental Convertor best et 10.679/127.5/1.533 60ft 308 gears best et 10.76/125.64/1.5471 |
#16
|
||||
|
||||
Quote:
__________________
|
#17
|
|||
|
|||
D ports..we're originally his 290cfm heads
__________________
466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2 373 gears 3200 Continental Convertor best et 10.679/127.5/1.533 60ft 308 gears best et 10.76/125.64/1.5471 |
#18
|
||||
|
||||
The 3:73 definitely going to help, over 3.08. Going to help the 60’s. So there KRE d-ports not e-head D-ports. This just me. I’d bring total timing all in by 1500 rpms. The Pro Systems advantage, going to be adjustability of idle air bleeds and high end air bleeds, of cruse figuring out what it’s going to like for high end air bleeds is going to be a challenge. With out tuning it on the dyno.
This might help, get some base runs in, then go up on high end air until it slows down, then go back. You might be surprise. One of the many things I’m sure you’ll play with.
__________________
|
#19
|
|||
|
|||
Quote:
__________________
466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2 373 gears 3200 Continental Convertor best et 10.679/127.5/1.533 60ft 308 gears best et 10.76/125.64/1.5471 |
#20
|
|||
|
|||
So here are some time slips in case someone is wondering why all the speculation on et. It also gives a time frame. 2019 is missing I installed the UCC convertor late that year and only 2 track days with dismal results and high convertor slippage in drive and loss of 60 foot..I blamed the convertor at the time but may have been the start of transmission issues. I think it ran 11.3/120mph?
2018 10.76/125.64 Holley 950 HP 308 gears 3200 convertor "healthy" trans 2020 10.88/127.13 Pro Systems Carb 308 gears 3200 convertor "not healthy trans? but at the time I thought the carb was giving up the 60 foot time 2021 11.04/125.42 Holley 950 HP 373 gears trans issues
__________________
466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2 373 gears 3200 Continental Convertor best et 10.679/127.5/1.533 60ft 308 gears best et 10.76/125.64/1.5471 |
The Following User Says Thank You to ta man For This Useful Post: | ||
Reply |
|
|