FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#1
|
||||
|
||||
Starter problems 70 TA
It cranks easy when cold, when hot it struggles badly. It seems like this is a common problem although, I never had it with my old birds back in the day.
There are a bunch of options for high torque starters, some with original look. What's the best option for performance and reliability? Will heat shields help? Thanks.
__________________
70 TA, 467 cid IAII, Edelbrock D-port heads, 9.94:1, Butler HR 236/242 @ .050, 520/540 lift, 112 LSA, Ray Klemm calibrated Q-jet, TKX (2.87 1st/.81 OD), 3.31 rear https://youtube.com/shorts/gG15nb4FWeo?feature=share |
#2
|
||||
|
||||
Back then GM had many problems with starters not reacting to heat well. The fix back then was a shield designed for Corvettes.
|
#3
|
||||
|
||||
My '70 had the same problem. My mechanic installed a high torque mini starter. It fixed the problem.
|
The Following User Says Thank You to napster For This Useful Post: | ||
#4
|
|||
|
|||
Lots of factors can affect this. Possibilities beyond just a weak starter: timing too far advanced, crappy gauge cables, cable routing too close to the block or manifolds. poor ground on the block.
|
The Following User Says Thank You to gto4evr For This Useful Post: | ||
#5
|
||||
|
||||
Quote:
Definitely check the grounds. Seems common on restored cars that stuff gets painted separately, and when reassembled the paint interferes with good metal-to-metal connections.
__________________
keith k 70 Trans Am RA III / T400 / Lucerne Blue / Bright Blue 70 Trans Am RA III / M20 / Lucerne Blue / Sandalwood 70 Formula RA III / M21 / Lucerne Blue / Bright Blue |
The Following User Says Thank You to keith k For This Useful Post: | ||
#6
|
||||
|
||||
Now, I am not old enough to recall these cars as new, or late model cars, but I had a crash course in this in the mid through late 1990's when I started driving mine daily.
After looking to ensure everything is well grounded, you should look at your starter; The common rebuilt starters do not use the better core starter - there are visual cues that the one you're looking at is a better one, or a run of the mill one. With the RA manifolds, there is virtually no clearance for heat shields, so that leaves you to needing a high heat solenoid. From my experience, the run of the mill starters will have a reduced diameter on the front, and the copper lead will pop through the case right at, or closer to the solenoid; The better ones have the full diameter of the starter carried right up to the front, and the copper lead for the solenoid will pop out near the very front of the case - and need an adapter to extend the connection to the solenoid. There are legitimate high heat solenoids both with GM part numbers and 'Standard' brand numbers, but I don't have any of those handy. Now, going away from original or OE replacement stuff, I have heard that the high torque mini starters work fantastic, as their smaller mass effectively helps them stay cooler. I hope this helps.
__________________
1970 Formula 400 Carousel Red paint on Black standard interior A no-engine, no-transmission, no-wheel option car. Quite likely one of few '70 Muncie three speed Formula 400's left. 1991 Grand Am: 14.4 @ 93.7mph (DA corrected) (retired DD, stock appearing) 2009 Cobalt SS: 13.9 @ 103mph (current DD; makes something north of 300hp & 350ft/lbs) |
The Following User Says Thank You to unruhjonny For This Useful Post: | ||
#7
|
||||
|
||||
Quote:
I remember identical setups with very different results for whatever reason.
__________________
_____________________________ She woke up sunny side down and I was still thinking I was too proud to flip her over |
The Following User Says Thank You to Wick For This Useful Post: | ||
#8
|
|||
|
|||
Glad I am not the only one having this issue, my 71 is still stuggling even with the RobbMC mini.
|
#9
|
||||
|
||||
one thing many people forget when upgrading from standard "log" manifolds to the RA units that the 70 RAIII/IV & 455HO/SD use is that they are a fair share larger;
Larger hold more heat, and the larger size puts the inside face closer to the starter
__________________
1970 Formula 400 Carousel Red paint on Black standard interior A no-engine, no-transmission, no-wheel option car. Quite likely one of few '70 Muncie three speed Formula 400's left. 1991 Grand Am: 14.4 @ 93.7mph (DA corrected) (retired DD, stock appearing) 2009 Cobalt SS: 13.9 @ 103mph (current DD; makes something north of 300hp & 350ft/lbs) |
#10
|
||||
|
||||
OTOH my Judge has never been a problem cranking. Have a vague memory of a different solenoid spring but was at least thutty yar ago.
|
#11
|
||||
|
||||
Quote:
At least not to my recollection; I had decades ago, help by one knowledgeable parts counter guy on getting a high heat solenoid - iirc they come with their specific spring.
__________________
1970 Formula 400 Carousel Red paint on Black standard interior A no-engine, no-transmission, no-wheel option car. Quite likely one of few '70 Muncie three speed Formula 400's left. 1991 Grand Am: 14.4 @ 93.7mph (DA corrected) (retired DD, stock appearing) 2009 Cobalt SS: 13.9 @ 103mph (current DD; makes something north of 300hp & 350ft/lbs) |
#12
|
||||
|
||||
Quote:
I also happen to know that there was an episode when I had a mechanic inspecting this car for me where the owner's people were not able to get it to start. Turns out the points were stuck and it wouldn't start. They didn't know that and kept cranking it until the battery died. I don't know but could that have damaged the starter? I'm going to check everything else too, of course, but one of the last things I need is a car that won't start. So since I don't have confidence in this starter, it's gotta go. Anyway, I have a new Powermaster Powermax Plus on the way from Summit.
__________________
70 TA, 467 cid IAII, Edelbrock D-port heads, 9.94:1, Butler HR 236/242 @ .050, 520/540 lift, 112 LSA, Ray Klemm calibrated Q-jet, TKX (2.87 1st/.81 OD), 3.31 rear https://youtube.com/shorts/gG15nb4FWeo?feature=share |
#13
|
|||
|
|||
Quote:
Replaced the solenoid and fabricated my own heat shield out of sheet metal. Still doing fine after all these years. |
The Following User Says Thank You to U47 For This Useful Post: | ||
#14
|
|||
|
|||
I’ve always had a lot of luck by upgrading to ‘0’ gauge cables. The best are bought at a stereo shop and often you need specific battery terminal connections for it but man what a difference!!
I’ve done this on several cars and it always makes a huge difference Take a look at this example- much better than anything your going to get at a parts store or reproduction. Just make sure to loom it… can’t have blue wire under the hood (you can get it in red/black) I promise you will see a significant difference https://www.amazon.com/KnuKonceptz-K.../dp/B004Z0WQZS |
#15
|
||||
|
||||
Like mentioned above, it's difficult these days to get a good rebuilt starter.
Most of the hot start problems I've seen are due to a worn armature, and those are almost never replaced with the cheap reman starters purchased at your local chain store. Almost all of your rebuild kits for the starters don't come with armatures either. I prefer to rebuild a good original GM starter myself with all the parts necessary, including the armature. I did the starter on my 70 RA III bird almost 25 years ago. I don't run heat shields, (As I recall, I don't believe 70 RA birds ever came with any heat shields of any kind. That didn't come along on the birds till later) I just have standard size battery cables, nothing fancy. It has buzzed the engine over without complaint for the last 100k miles or so. I drive the car regularly and the AZ heat doesn't bother it. Just something else to think about. |
#16
|
||||
|
||||
I deal with this too, especially in hot weather.
What's a good heat shield for a 400?
__________________
"A MAN IS ONLY AS OLD AS THE WOMAN HE FEELS." -- Groucho Marx |
#17
|
|||
|
|||
I have run headers since the 80's in my 76 455. Always had hot start problems, and maybe it was simply due to the headers. I went through a variety of fixes over the years. Rewound OEM, new OEM, heat shields, better cables, wrap (both the starter and the headers) and etc. The heat shields and wraps improved things but did not solve the problem. I went to a high torque mini starter a few years ago and never a problem since.
|
#18
|
||||
|
||||
My car has the OEM style spring clamp terminal battery cables. I have to replace those anyway so I can attach my trickle charge cables. But, I'm also putting in a Powermaster Powermax Plus mini starter.
__________________
70 TA, 467 cid IAII, Edelbrock D-port heads, 9.94:1, Butler HR 236/242 @ .050, 520/540 lift, 112 LSA, Ray Klemm calibrated Q-jet, TKX (2.87 1st/.81 OD), 3.31 rear https://youtube.com/shorts/gG15nb4FWeo?feature=share |
#19
|
||||
|
||||
Quote:
The "big 3" upgrade makes a difference with charging as well. I have a large stereo system in my Tahoe and I'll tell you that wiring can make a huge difference. https://gpcaraudio.com/1-0-awg-pre-t...p-merica-ofhc/
__________________
James 1970 Trans Am Spotts Built 484" IA2, Highports, EFI Northwind Terminator X sequential EFI fabrication and suspension by https://www.funkhouserracecars.com/ |
Reply |
|
|