Forum: Pontiac - Street
05-24-2024, 09:53 PM
|
Replies: 3
Views: 114
Pushrod length
I have KRE's. Since they and Edelbrocks require the same aftermarket head bolts I'm going to go out on a limb and say the push rod length requirement would be the same or similar. I have an HFT cam...
|
Forum: Pontiac - Street
05-24-2024, 12:31 PM
|
Replies: 1
Views: 70
TH350 accumulator spring missing
There are two accumulators on the TH350 . One is on the case outside near the tail. The other is installed in the valve body and covers the band apply servo. The valve body accumulator spring was ...
|
Forum: Pontiac - Street
05-24-2024, 02:49 AM
|
Replies: 22
Views: 781
I think a good idea would be to go back to...
I think a good idea would be to go back to 'Street' page and do a search for mild, or street builds. Cams for a street build. Compression ratios for a street build. Head decking/cutting. Zero...
|
Forum: Pontiac - Street
05-23-2024, 12:07 PM
|
Replies: 22
Views: 781
|
Forum: Pontiac - Street
05-23-2024, 12:47 AM
|
Replies: 22
Views: 781
|
Forum: Pontiac - Street
05-22-2024, 08:52 PM
|
Replies: 22
Views: 781
My 408 with #48 heads (chambers measured at 70...
My 408 with #48 heads (chambers measured at 70 cc) was 9:1 cr. Cast 8 valve relief pistons .040 in the hole. Detonated badly. Octane booster was a no go. Pistons changed to Speedpro (TRW) .026 in the...
|
Forum: THE LOBBY
05-20-2024, 11:16 PM
|
Replies: 22
Views: 683
|
Forum: THE LOBBY
05-20-2024, 11:12 PM
|
Replies: 16
Views: 659
|
Forum: THE LOBBY
05-20-2024, 10:54 PM
|
Replies: 58
Views: 1,317
|
Forum: THE LOBBY
05-15-2024, 10:11 PM
|
Replies: 37
Views: 3,874
|
Forum: Pontiac - Street
05-13-2024, 06:10 PM
|
Replies: 10
Views: 367
|
Forum: THE LOBBY
05-13-2024, 08:31 AM
|
Replies: 8
Views: 515
|
Forum: THE LOBBY
05-12-2024, 10:40 PM
|
Replies: 8
Views: 515
Facebook scam?
This facebook page showed up on my news feed: Classic Auto Parts For Sale
I am in the process of doing a purchase. The e mail address I have been given via messaging to do a paypal transaction...
|
Forum: Pontiac - Street
04-30-2024, 04:08 PM
|
Replies: 10
Views: 626
I helped my daughter do a brake job on her 17...
I helped my daughter do a brake job on her 17 Escape. The caliper bracket bolts required torquing. Reused the front bolts no problem. However, one of the rears deformed well below the required torque...
|
Forum: Pontiac - Street
04-29-2024, 10:01 PM
|
Replies: 10
Views: 626
|
Forum: THE LOBBY
04-23-2024, 01:01 PM
|
Replies: 13
Views: 1,679
|
Forum: Pontiac - Race
04-01-2024, 09:24 PM
|
Replies: 16
Views: 784
|
Forum: Industry Stuff
04-01-2024, 07:49 PM
|
Replies: 7
Views: 1,606
|
Forum: Members Helping Members
03-26-2024, 08:25 PM
|
Replies: 8
Views: 729
|
Forum: Pontiac - Street
03-24-2024, 10:30 PM
|
Replies: 6
Views: 525
|
Forum: Pontiac - Street
03-24-2024, 10:22 PM
|
Replies: 6
Views: 525
Thanks for the response, guys.
As I'm...
Thanks for the response, guys.
As I'm cleaning and inspecting I saw that the direct drum had 5 steels/frictions instead of 4. The pressure/backing plate has only a very small lip on the surface...
|
Forum: THE LOBBY
03-21-2024, 08:19 PM
|
Replies: 559
Views: 40,824
Did not start this today
I decided to get into this TH350 that quit a couple of years ago. Hard upshifts finally resulted in a bigger bang.
...
|
Forum: THE LOBBY
03-21-2024, 07:29 PM
|
Replies: 559
Views: 40,824
|
Forum: Pontiac - Street
03-20-2024, 11:22 PM
|
Replies: 6
Views: 525
TH350 question
I am resurrecting a TH350 that lost all the gears (except park and neutral:D).
I have it disassembled up to the center support and low/reverse clutches.
The forward and direct drums are...
|
Forum: THE LOBBY
03-18-2024, 11:19 PM
|
Replies: 29
Views: 1,625
I have not; but I have eaten eel while in New...
I have not; but I have eaten eel while in New Zealand. I think the anatomy is very similar. Among other delicacies it was cooked using geothermal steam. As I recall the flavour was mild. It was less...
|