Reply
 
Thread Tools Display Modes
  #1  
Old 05-11-2011, 06:08 PM
71ModelJ's Avatar
71ModelJ 71ModelJ is offline
Senior Member
 
Join Date: Nov 2010
Location: Northwood N.H.
Posts: 147
Default Fuel guage inop

O.K. Fuel guage inop. pulled sender wire off near tank and gauge did not drop. Guage is stuck. Question is there are no screws on dash bezel. How do I access gauge. Are the bezels clipped in? Help!

  #2  
Old 05-11-2011, 08:00 PM
428ho4spd's Avatar
428ho4spd 428ho4spd is offline
Ultimate Warrior
 
Join Date: May 2006
Location: CA
Posts: 1,374
Default

I wouldn't think that the guage is bad. Did you ground the terminal inside the connector by the trunk latch that leads to the gauge? Guage should drop to empty when grounded. The cluster is removed from the back side of the inst panel, then you'll have to go from there... Hope that helps!

  #3  
Old 05-12-2011, 05:28 AM
71ModelJ's Avatar
71ModelJ 71ModelJ is offline
Senior Member
 
Join Date: Nov 2010
Location: Northwood N.H.
Posts: 147
Default

Quote:
Originally Posted by 428ho4spd View Post
I wouldn't think that the guage is bad. Did you ground the terminal inside the connector by the trunk latch that leads to the gauge? Guage should drop to empty when grounded. The cluster is removed from the back side of the inst panel, then you'll have to go from there... Hope that helps!
I thought it pinned the gauge when grounded?

  #4  
Old 05-12-2011, 10:20 AM
428ho4spd's Avatar
428ho4spd 428ho4spd is offline
Ultimate Warrior
 
Join Date: May 2006
Location: CA
Posts: 1,374
Default

The gauge usually reads past full when the sender is bad. Grounding it will move it back to empty. What problem are you having exactly?

  #5  
Old 05-12-2011, 11:51 AM
mike nixon mike nixon is offline
Moderator
 
Join Date: Dec 1999
Location: PORTLAND,IN,47371
Posts: 12,322
Default

If you're wanting to pull the guage itself it's easier to pull the dash lay it on the seat and remove the guage. You can get it out from behind but it's a ROYAL PITA to do so. Fasteners are all from the rear on the 69-72 cars.

I'd be looking the sending unit over carefully. Most problems I see with these cars are there.

Mike

__________________
so many pontiacs, so little time..................


moderator is a glorified word for an unappreciated prick..................


"Only two things are infinite, the universe and human stupidity, and I'm not sure about the
former." --Albert Einstein



"There is no such thing as a good tax."

"We contend that for a nation to tax itself into prosperity is like a man standing in a bucket and trying to lift himself up by the handle."

- Winston Churchill
  #6  
Old 05-13-2011, 10:30 AM
71ModelJ's Avatar
71ModelJ 71ModelJ is offline
Senior Member
 
Join Date: Nov 2010
Location: Northwood N.H.
Posts: 147
Default

Quote:
Originally Posted by 428ho4spd View Post
The gauge usually reads past full when the sender is bad. Grounding it will move it back to empty. What problem are you having exactly?
It's pinned all the time. I grounded it and it didn't move. I'll make sure I have a better ground and try again. Thank's Mike

Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:54 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017