Forum: THE LOBBY
06-10-2024, 04:49 PM
|
|
Replies: 7
Views: 600
Another laughable Pontiac article.
The long and the short ... "The RAV was cancelled due to the pushrod supplier filing BK. I can just hear the boardroom discussion:
Purchasing Dept Head "I got some bad news boys. Ummm, the...
|
|
Forum: THE LOBBY
06-10-2024, 01:40 PM
|
|
Replies: 62
Views: 4,313
|
|
Forum: Pontiac - Street
06-10-2024, 10:19 AM
|
|
Replies: 20
Views: 419
|
|
Forum: THE LOBBY
06-10-2024, 09:14 AM
|
|
Replies: 62
Views: 4,313
|
|
Forum: THE LOBBY
06-10-2024, 08:16 AM
|
|
Replies: 62
Views: 4,313
|
|
Forum: Pontiac - Race
06-07-2024, 12:48 PM
|
|
Replies: 22
Views: 913
The reduction of weight can be important.
In...
The reduction of weight can be important.
In 2003 David Vizard published an article titled the "wonder Spring".
Consider the valvetrain mass in a Big Block Chevy with 2.300" intake valves. ...
|
|
Forum: Pontiac - Race
06-07-2024, 09:29 AM
|
|
Replies: 22
Views: 913
Beehive pressures for HR cams
Beehives are the new big deal(whether real or not). Since retainer smaller and lighter they say you can use less valve spring pressure -but how much lighter is OK for an HR?
LS motors that use a...
|
|
Forum: THE LOBBY
06-06-2024, 01:58 AM
|
|
Replies: 16
Views: 837
|
|
Forum: THE LOBBY
06-04-2024, 11:10 PM
|
|
Replies: 5
Views: 400
|
|
Forum: Pontiac - Street
06-03-2024, 01:29 PM
|
|
Replies: 9
Views: 436
Casting flaw.
I’ve seen several block that...
Casting flaw.
I’ve seen several block that were missing material in that exact spot at the back near the distributor due to an incomplete pour at the foundry.
The ones above the lifter bores...
|
|
Forum: Pontiac - Street
06-01-2024, 07:34 PM
|
|
Replies: 30
Views: 1,242
if you had vac adv plugged in when you checked...
if you had vac adv plugged in when you checked for the 37 thats your problem .
the whole purpose of springs out timing check is to set total timing with full mech adv only and you dont have to rev...
|
|
Forum: Pontiac - Street
06-01-2024, 07:09 PM
|
|
Replies: 30
Views: 1,242
|
|
Forum: THE LOBBY
05-31-2024, 09:37 PM
|
|
Replies: 14
Views: 654
|
|
Forum: Pontiac - Street
05-31-2024, 10:25 AM
|
|
Replies: 35
Views: 945
Seconding the 4l80e. For what you're doing a...
Seconding the 4l80e. For what you're doing a stock rebuild with a stock type converter is all you need. Here's some tips on install that will be really helpful.
Find a 1994-1996 2wd model...
|
|
Forum: THE LOBBY
05-29-2024, 08:09 AM
|
|
Replies: 14
Views: 654
Prayers needed for 3 persons.
First myself. It's been since last spring. Swollen lymph nodes in chest(found out through testing sinus infection). Then PET scan,initially thought from scan ,cancer in prostate. Finally no. Then...
|
|
Forum: Pontiac - Street
05-28-2024, 03:43 PM
|
|
Replies: 13
Views: 781
|
|
Forum: Pontiac - Street
05-28-2024, 02:38 PM
|
|
Replies: 17
Views: 838
As noted, parts are hard to find. My car had a...
As noted, parts are hard to find. My car had a 12/10 bolt 3.23 rear in it when purchased in 1985. It has taken a beating with no issues. I did find and install new clutch plates and a heavy duty "S"...
|
|
Forum: Pontiac - Street
05-28-2024, 07:35 AM
|
|
Replies: 17
Views: 838
|
|
Forum: Pontiac - Street
05-26-2024, 06:51 PM
|
|
Replies: 17
Views: 838
TYPE "O" OLDS TEN bolts
4 different housings:
-'67-69 standard 28 spline sealed axle bearing end housings
used all three model years on all single track & high ratio Anti-Spin rears,
-'70 Tapered bearing housing...
|
|
Forum: Pontiac - Street
05-26-2024, 12:29 PM
|
|
Replies: 17
Views: 838
|
|
Forum: THE LOBBY
05-26-2024, 12:17 PM
|
|
Replies: 101
Views: 4,579
|
|
Forum: THE LOBBY
05-23-2024, 01:35 PM
|
|
Replies: 101
Views: 4,579
|
|
Forum: Pontiac - Street
05-23-2024, 04:24 AM
|
|
Replies: 15
Views: 548
|
|
Forum: THE LOBBY
05-22-2024, 06:49 AM
|
|
Replies: 134
Views: 3,320
|
|
Forum: THE LOBBY
05-20-2024, 11:46 PM
|
|
Replies: 134
Views: 3,320
|
