[Jeff Kinsler]

cant believe still no cv1 cars!!! if Robin was there I would go and give him a run.

[LiL Jack]

Originally Posted by Jeff Kinsler

cant believe still no cv1 cars!!! if Robin was there I would go and where his chit out.

FIXED

[LiL Jack]

Originally Posted by jdw_poncho

I hate to admit this on the forum but I have to throw the towel in. I was getting it ready to fire up late last night and found out my t400 case is cracked between the fittings. Not sure when it happened but I think its when I dropped the cooler on the floor. I had it still hooked up and the cooler was ziptied up out of the way and it broke loose and yanked the hoses pretty hard since the car was 2' in the air. I suspect it was already cracked and this could have just made it worse.

I had a very small leak last year which I thought was a pan gasket. Im thinking it was weeping from it and I just couldnt see.

Guess Im bringing cold beer for the ECM since my cv-1's wont be there.

I have M&M local to me so I might call and see if they can get me done in time. Its still possible.....

At least u found it know instead of going down the track.

[Stan Weiss]

Originally Posted by ho428

CV1 Catagories at Norwalk:
Pro Bench
Pro Calculator
Pro Dyno
Pro Engine Stand

Instead of a 10.5 class we'll have a 10.4
"Can your make believe engine out run a real one?"
"Ten Four"

Based on some of the replies in this thread I think you missed what will be the most popular non-CV-1 category

Pro BS'er

Stan

[ho428]

Originally Posted by Stan Weiss

Based on some of the replies in this thread I think you missed what will be the most popular non-CV-1 category

Pro BS'er

Stan

Now that's a serious heads up class...

[johnta1]

Based on some of the replies in this thread I think you missed what will be the most popular non-CV-1 category

Pro BS'er

X2!

[PONTIAC DUDE]

Since they came out in 2007........... it's now 2013.
Been 7 years plus in development.

[Blued and Painted]

Originally Posted by David Holmberg

Can we bring Dyno sheets too?

Liar's poker with dyno sheets. I've got three 3's @ 4800

[LiL Jack]

Originally Posted by PONTIAC DUDE

Since they came out in 2007........... it's now 2013.
Been 7 years plus in development.

It's the economy!

[Stan Weiss]

Originally Posted by Blued and Painted

Liar's poker with dyno sheets. I've got three 3's

They are just a piece of page. What do you want it to say?

Stan


_Horse__________RPM_________Torque___________BMEP
_541.931_______4100________694.201________193.503
_568.795_______4200________711.265________198.260
_595.730_______4300________727.622________202.819
_622.691_______4400________743.267________207.180
_649.631_______4500________758.191________211.340
_676.495_______4600________772.381________215.295
_703.230_______4700________785.822________219.042
_729.778_______4800________798.499________222.576
_756.083_______4900________810.397________225.892
_782.086_______5000________821.503________228.988
_807.731_______5100________831.805________231.859
_832.965_______5200________841.295________234.505
_857.735_______5300________849.967________236.922
_881.991_______5400________857.818________239.110
_905.687_______5500________864.849________241.070
_928.780_______5600________871.063________242.802
_951.231_______5700________876.467________244.309
_973.004_______5800________881.072________245.592
_994.067_______5900________884.888________246.656
1014.392_______6000________887.931________247.504
1033.954_______6100________890.218________248.142
1052.733_______6200________891.766________248.573
1070.708_______6300________892.597________248.805
1087.864_______6400________892.728________248.841
1104.186_______6500________892.183________248.689
1119.662_______6600________890.979________248.354
1134.277_______6700________889.138________247.841
1148.019_______6800________886.676________247.154
1160.873_______6900________883.610________246.300
1172.822_______7000________879.952________245.280
1183.846_______7100________875.713________244.098
1193.919_______7200________870.897________242.756
1203.009_______7300________865.508________241.254
1211.079_______7400________859.539________239.590
1218.080_______7500________852.981________237.762
1223.954_______7600________845.817________235.765
1228.632_______7700________838.022________233.592
1232.027_______7800________829.565________231.235
1234.040_______7900________820.402________228.681
1234.553_______8000________810.484________225.916
1233.428_______8100________799.748________222.924
1230.504_______8200________788.123________219.683
1225.596_______8300________775.522________216.171
1218.494_______8400________761.849________212.360
1208.957_______8500________746.993________208.219
1196.713_______8600________730.830________203.713
1181.455_______8700________713.219________198.804

Average_Horsepower_=__1011.009
Average_Torque______=_828.625
Average_based_on_=_47_points

[Blued and Painted]

Your not supposed to show your hand!
But it looks like your TTFMF with 1234 @8000. You can't use that sheet again.

[mjm421]

Originally Posted by PONTIAC DUDE

Since they came out in 2007........... it's now 2013.
Been 7 years plus in development.

We wasted 2 years waiting on you to do something with em. You may be a good engine builder, but as we all now know you really aren't capable to do r&d work. You're much better at picking up the phone and using someone else's product. You and your brother from another mother Lou are the biggest detriment to these heads. BTW you are the ONLY ONE to go slower with these heads. Just sayin

[Hooter]

Originally Posted by mjm421

We wasted 2 years waiting on you to do something with em. You may be a good engine builder, but as we all now know you really aren't capable to do r&d work. You're much better at picking up the phone and using someone else's product. You and your brother from another mother Lou are the biggest detriment to these heads. BTW you are the ONLY ONE to go slower with these heads. Just sayin

DIDTHATJUSTHAPPEN

[russ467]

YIKES!!!

[BADDTA]

Originally Posted by mjm421

We wasted 2 years waiting on you to do something with em. You may be a good engine builder, but as we all now know you really aren't capable to do r&d work. You're much better at picking up the phone and using someone else's product. You and your brother from another mother Lou are the biggest detriment to these heads. BTW you are the ONLY ONE to go slower with these heads. Just sayin

Brian

[Rob B]

Originally Posted by Hooter

DIDTHATJUSTHAPPEN

ITSURETHEPHUCKDID!
Dammmmmmmmmnnnnnnn!

[twinturrbo406]

Originally Posted by mjm421

We wasted 2 years waiting on you to do something with em. You may be a good engine builder, but as we all now know you really aren't capable to do r&d work. You're much better at picking up the phone and using someone else's product. You and your brother from another mother Lou are the biggest detriment to these heads. BTW you are the ONLY ONE to go slower with these heads. Just sayin

... WOW ...

... I do like how he thinks since the very first day Roland got his hands on a casting, they were under "Development", lol the actual time the CV-1 was available, was March of 2008, which by my CV-1 Calculator is a little over 5 years ...

... The Race Shop released it's CNC CV-1 based on a porters casting mid-2009, which actually flowed 385cfm by the way, which most people do not consider to be any kind of development for this head ...

... my work did not really begin until 2010, and even then it pales in comparison to what has happened in the last year ...

[Jeff Kinsler]

Originally Posted by twinturrbo406

... WOW ...

... I do like how he thinks since the very first day Roland got his hands on a casting, they were under "Development", lol the actual time the CV-1 was for available, was March of 2008, which by my CV-1 Calculator is a little over 5 years ...

... The Race Shop released it's CNC CV-1 based on a porters casting mid-2009, which actually flowed 385cfm by the way, which I do not consider to be any kind of development for this head ...

... my work did not really begin until 2010, and even then it pales in comparison to what has happened in the last year ...

just get your car to norwalk!!

[twinturrbo406]

Originally Posted by Jeff Kinsler

just get your car to norwalk!!

... working on it Jeff ...

[PONTIAC DUDE]

Originally Posted by mjm421

We wasted 2 years waiting on you to do something with em. You may be a good engine builder, but as we all now know you really aren't capable to do r&d work. You're much better at picking up the phone and using someone else's product. You and your brother from another mother Lou are the biggest detriment to these heads. BTW you are the ONLY ONE to go slower with these heads. Just sayin

Actually I got screwed out of Ten grand with stepping up with the heads and not following thru on a commitment to go X275 racing with them. Everyone else just wants to play with em. So we will never know the capability of them. Might have been able to put em on the map. Never know now.