Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Showing results 1 to 14 of 14
Search took 0.03 seconds. Search: Posts Made By: Flashflood
Forum: 73-77 A-body TECH 05-03-2026, 08:34 PM
Replies: 2
Views: 236
Posted By gtoguys
This Can Am is a Pontiac 400. Thanks for offering...

This Can Am is a Pontiac 400. Thanks for offering with the 403.
Forum: 73-77 A-body TECH 04-13-2026, 08:48 PM
Replies: 17
Views: 2,288
Posted By Mr. G
Try plugging the bulb sockets into the old bulbs...

Try plugging the bulb sockets into the old bulbs without mounting them just to verify the new bulbs are not defective.
Forum: 73-77 A-body TECH 02-23-2026, 01:13 PM
Replies: 4
Views: 356
Posted By Mr. G
What is the fuel gauge reading? There should be a...

What is the fuel gauge reading? There should be a connector near the area where the wire passes from inside of the trunk to the outside usually somewhere near the license plate mount. If you can find...
Forum: 73-77 A-body TECH 02-16-2026, 11:27 AM
Replies: 5
Views: 486
Posted By TXSTARFIRE
I think hangars are usually mounted to the frame...

I think hangars are usually mounted to the frame not the floor. I would just duplicate the mount locations of an earlier car that came with dual exhaust. Might need an earlier cross member.
Forum: 73-77 A-body TECH 01-26-2026, 05:59 PM
Replies: 10
Views: 499
Posted By OG68
Long thin blade screwdriver for the snap ring. ...

Long thin blade screwdriver for the snap ring. Pry up between ring and column housing.

You need to pull the signal switch up and out of the way to access the four hex headed screws that hold the...
Forum: 73-77 A-body TECH 01-13-2026, 12:46 PM
Replies: 3
Views: 626
Posted By importsmasher
I have a 75 (non-Luxury) LeMans that has the...

I have a 75 (non-Luxury) LeMans that has the inside hood release. I wasn't aware it was optional. As referenced above, my 74 Grand Am and my 73 GA parts car both have the inside release.
...
Forum: 73-77 A-body TECH 01-12-2026, 01:56 PM
Replies: 6
Views: 451
Posted By johnta1
This is what the switch looks like probably....

This is what the switch looks like probably. (Firebird but should look about same)


https://maxperformanceinc.com/wp-content/uploads/2024/01/rfi243b.jpg




The plug connector for the...
Forum: 61-77 GTO, Tempest & LeMans Parts WANTED 03-26-2025, 01:52 PM
Replies: 6
Views: 2,927
Posted By ROCKETMAN269V
75 to 77 Olds 350 alternator bracket

I have most every Olds engine bracket ever made. Do you have a/c or not? Any image or illustration of what you need. Thanks, Bob. :usflag:
Forum: 73-77 A-body TECH 07-02-2024, 05:37 PM
Replies: 3
Views: 2,979
Posted By 694.1
Maye some kind of obstruction? A well oiled...

Maye some kind of obstruction?
A well oiled fresh build would take some serious neglect to be unable to be turned. Try the flywheel end.
Forum: 73-77 A-body TECH 04-21-2024, 04:04 PM
Replies: 1
Views: 4,552
Posted By cdrookie
Look for headers from a 2nd gen T/A with the 403....

Look for headers from a 2nd gen T/A with the 403. I'm not saying they'll fit but I know the 2nd gen F body Pontiac headers fit a Pontiac engine in a 73-77 A body.
Forum: 73-77 A-body TECH 07-13-2021, 09:37 AM
Replies: 9
Views: 4,080
Posted By cdrookie
They should be 3/8" bolts, the head can be...

They should be 3/8" bolts, the head can be different than the typical 9/16 depending on the type or fastener. They should not be metric.
Forum: 73-77 A-body TECH 06-24-2021, 02:53 AM
Replies: 1
Views: 2,540
Posted By Brian Baker
If the transmission is not sitting on it and you...

If the transmission is not sitting on it and you have all 4 bolts that mount it to the frame (two on each side) removed, it should come loose. Try budging it with a rubber mallet.
Forum: 73-77 A-body TECH 06-17-2021, 02:37 AM
Replies: 5
Views: 3,132
Posted By Brian Baker
Not necessarily. If you unbolt the transmission...

Not necessarily. If you unbolt the transmission from the crossmember mount at the top, leaving the mount attached to the crossmember, the tailshaft should slide right off. Having a friend under the...
Forum: 73-77 A-body TECH 08-05-2020, 11:32 PM
Replies: 3
Views: 2,309
Posted By Sirrotica
Olds and Pontiac are similar, but not the same,...

Olds and Pontiac are similar, but not the same, neither is particularly tough to do. If you work at a decent pace 2-3 hours. Flat rate would pay maybe 1.5 hours start to finish.

You might buy a...
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT -4. The time now is 11:13 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017