Forum: Heating & Cooling TECH
04-14-2013, 11:08 PM
|
|
Replies: 9
Views: 483
|
|
Forum: Heating & Cooling TECH
04-14-2013, 03:15 PM
|
|
Replies: 9
Views: 483
|
|
Forum: Pontiac - Street
04-04-2013, 12:33 PM
|
|
Replies: 17
Views: 888
on a lock-up converter for a 700R4 how far can...
on a lock-up converter for a 700R4 how far can the 1/8" plug screw in before it contacts moving parts?
Would there be any problems with adding 2 drain plugs 180 degrees apart to preserve balance or...
|
|
Forum: Pontiac - Street
06-24-2012, 12:26 PM
|
|
Replies: 10
Views: 599
|
|
Forum: Pontiac - Street
05-08-2012, 02:13 PM
|
|
Replies: 15
Views: 1,024
I would just buy the kit from Cliff.
That is...
I would just buy the kit from Cliff.
That is what I did and He is very helpful.
I was able to email Cliff and get responses about what goes where when I was confused.
Rebuilding my carb with his...
|
|
Forum: The Body Shop TECH
05-04-2012, 10:40 PM
|
|
Replies: 23
Views: 3,252
|
|
Forum: The Body Shop TECH
05-02-2012, 05:30 PM
|
|
Replies: 23
Views: 3,252
Painting over POR 15
Hay guys, my car had the underside, subframe, and firewall coated with POR 15 by the previous owner. It was done with a paint brush and left brush marks on the cowel. I would like to paint this...
|
|
Forum: The Body Shop TECH
04-26-2012, 07:21 PM
|
|
Replies: 6
Views: 341
|
|
Forum: The Body Shop TECH
04-26-2012, 10:27 AM
|
|
Replies: 6
Views: 341
|
|
Forum: The Body Shop TECH
04-25-2012, 11:30 PM
|
|
Replies: 6
Views: 341
DTM Epoxy on the interior?
I am redoing my interior and the previous owner stripped it down to bare metal.
Should I use DTM Epoxy on it?
I am going with a black interior, what amount of gloss should the paint be?
Thanks
...
|
|
Forum: Pontiac - Street
04-19-2012, 09:33 PM
|
|
Replies: 4
Views: 431
|
|
Forum: Pontiac - Street
03-22-2012, 02:38 PM
|
|
Replies: 5
Views: 536
Thank you for the replies.
I was thinking the...
Thank you for the replies.
I was thinking the sealed power 4040M-10 main bearings and the Clevite CB758HN10 rod bearings.
I have a new M54DS pump that I tack welded the pick onto and installed the...
|
|
Forum: Pontiac - Street
03-21-2012, 12:23 PM
|
|
Replies: 5
Views: 536
Race bearings for the street?
I need to replace the bearings in my 400 after a bad initial start up experience.
Are race bearings a good choice for a street engine not seeing the high side of 5500rpm?
I have read some of the...
|
|
Forum: Pontiac - Street
03-09-2012, 11:46 PM
|
|
Replies: 27
Views: 2,815
9.15" it is.
I re-checked my pushrod length...
9.15" it is.
I re-checked my pushrod length using 9.1", 9.15", and 9.2".
9.1" gave me a pattern about center.
9.15" gave me a pattern just to the exhaust side of center.
These checks where with...
|
|
Forum: Pontiac - Street
03-09-2012, 03:04 PM
|
|
Replies: 27
Views: 2,815
|
|
Forum: Pontiac - Race
03-07-2012, 03:32 PM
|
|
Replies: 4
Views: 491
Living in the Edmonton area as well I have...
Living in the Edmonton area as well I have learned to avoid UPS for shipping from the US.
If I can't get an item shipped by USPS I now go else where.
The few times I have had to use UPS I never...
|
|
Forum: Pontiac - Street
03-01-2012, 12:04 PM
|
|
Replies: 27
Views: 2,815
I never checked to see how close I am to 90...
I never checked to see how close I am to 90 degrees at mid lift. I will give this a look.
I have no binding or rubbing in my valve train so I think I will run it as is. I do agree that the push rods...
|
|
Forum: Pontiac - Street
03-01-2012, 11:41 AM
|
|
Replies: 14
Views: 633
blue bayou, from what I have seen GM used...
blue bayou, from what I have seen GM used different pitman/idler arm lengths combined with different steering arms (I am not sure if steering arm is the proper name but it is the part attached to the...
|
|
Forum: Pontiac - Street
02-28-2012, 11:10 PM
|
|
Replies: 27
Views: 2,815
|
|
Forum: Pontiac - Street
02-28-2012, 03:21 PM
|
|
Replies: 27
Views: 2,815
Just a little information on this.
Summit 2802...
Just a little information on this.
Summit 2802 cam and lifter kit.
HS 1.5 rockers
Heads and block have not been milled or decked. .038 crush head gaskets.
Heads are 670s with longer than normal...
|
|
Forum: Pontiac - Street
02-28-2012, 11:38 AM
|
|
Replies: 27
Views: 2,815
|
|
Forum: Pontiac - Street
02-28-2012, 01:06 AM
|
|
Replies: 35
Views: 1,426
|
|
Forum: Pontiac - Street
02-28-2012, 12:54 AM
|
|
Replies: 27
Views: 2,815
Valve stem wear pattern
After cam break in, I checked my valve stem wear pattern and found this. Does this show to long or short a push rod? I am thinking to long.
|
|
Forum: Pontiac - Street
02-27-2012, 12:27 AM
|
|
Replies: 35
Views: 1,426
|
|
Forum: Pontiac - Street
02-26-2012, 11:54 PM
|
|
Replies: 35
Views: 1,426
|
