Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Page 1 of 3 1 23
Showing results 1 to 25 of 61
Search took 0.02 seconds. Search: Posts Made By: ironman
Forum: Non Pontiac Motors in Pontiacs 06-21-2014, 01:34 AM
Replies: 2
Views: 1,100
Posted By ironman
SBC cam specs

Anybody have an older Howard cams catalogue, need the specs for a solid flat SBC grind marked 345g and 1129
Thanks
Forum: Pontiac - Street 08-25-2013, 07:48 PM
Replies: 1
Views: 512
Posted By ironman
comp 290-B

Want to run a 461 in a 68 firebird, Forged Mahle pistons eagle 4.25 crank, eagle 6.8 rods zero decked block ported 6S iron heads milled to 95 CC flowed at 230 on the intake 9.5 compression and ported...
Forum: Pontiac - Street 05-24-2013, 07:51 PM
Replies: 11
Views: 642
Posted By ironman
carby emptying over night takes a while to wind...

carby emptying over night takes a while to wind engine over on first start up to fill carby thought an electric pump may cure this, could it be a problem with the existing pump, it is an aftermarket...
Forum: Pontiac - Street 05-23-2013, 09:05 PM
Replies: 11
Views: 642
Posted By ironman
Fuel Pump

Looking to run an electric fuel pump in my 68 firebird, 455 with a Quadrajet. Need advice on pressure I don't want to run a regulator if i can avoid it. Looking at the carter P4070 or P4594...
Forum: Pontiac - Street 04-25-2013, 05:44 AM
Replies: 2
Views: 384
Posted By ironman
Which Crower lifter

Need a set of cool face solid lifters to suit a crower 60311 I am getting conflicting part numbers for the lifters. 66962x980-16 and 66963x980-16. Which ones do I need and what is the difference, the...
Forum: Pontiac - Street 04-20-2013, 02:43 AM
Replies: 3
Views: 557
Posted By ironman
Rod bearings

Guys,
Need part numbers for rod bearings. Eagle 4.25" cast crank BBC 2.2" journals eagle 6.8" rods. Not all that fussed with brand preference.

Thanks
Forum: Pontiac - Street 04-16-2013, 01:18 AM
Replies: 2
Views: 431
Posted By ironman
Where to buy engine parts

Guys,
I will be in Los angeles next month I want to pick up some engine parts whilst there, basically pistons, bearings and a camshaft specifically a crower 60311 as well as other bits...
Forum: Pontiac - Street 03-25-2013, 05:51 AM
Replies: 1
Views: 626
Posted By ironman
8.5" rear

Recently found what I think is an 8.5" 10 bolt. Having some trouble identifying it. It has a completely smooth round cover and the yoke is round looks like the tail shaft bolts on using bolts through...
Forum: Pontiac - Street 02-03-2013, 12:41 AM
Replies: 6
Views: 861
Posted By ironman
Offset grind crank

Wanting to offset grind my factory 455 crank to BBC size to increase stroke to 4.25. Not normally a problem but the crank has a fresh unused .010" grind on it. This would leave one side of the...
Forum: Pontiac - Street 11-10-2012, 09:04 PM
Replies: 1
Views: 408
Posted By ironman
Valve spring coil bind

Been buying parts as I find them for a future build. I have a set of Comp 26995 beehive springs that I will install at 1.7 and a set of comp 1.65 roller rockers, I want to run a crower 60311 solid...
Forum: Pontiac - Street 10-03-2012, 09:06 PM
Replies: 3
Views: 752
Posted By ironman
Crower 60310 OR 60311

Building a 455 +30 6x-8 heads milled to 95 cc ported to 230 zero deck forged pistons and rods looking at about 9.5 to 1 compression iron intake with 8oo cfm quadrajet th350 with 2800/3000 convertor...
Forum: Pontiac - Street 08-09-2012, 09:01 PM
Replies: 10
Views: 3,579
Posted By ironman
041 cam

Looking to buy a cam with factory 041 specs. I know there are a few after market choices out there was looking at the comp cams 041h is this a good choice as far as matching the factory specs, if not...
Forum: Pontiac - Street 04-08-2012, 06:51 AM
Replies: 5
Views: 876
Posted By ironman
Turbo 400 trans

I have a line on a T/H 400 that I want to fit to my 68 fire bird. It is the long tail version is the one to use or would a short tail be better in this application.

Thanks
Forum: Pontiac - Street 02-09-2012, 02:52 AM
Replies: 1
Views: 309
Posted By ironman
Windscreen washers

Can anybody tell me or show me a picture where and how the windscreen washer nozzles attach on a 1968 fire bird,

Thanks
Forum: The Body Shop TECH 01-01-2012, 07:27 PM
Replies: 1
Views: 252
Posted By ironman
windscreen mouldings

Trying to put my 68 firebird coupe back together. I have no idea how the bottom moulding at the front screen is attached. It obviously needs clips but what do they look like and where do they fit.
...
Forum: Pontiac - Street 12-31-2011, 11:40 PM
Replies: 0
Views: 201
Posted By ironman
windscreen mouldings

Trying to put my 68 firebird coupe back together. I have no idea how the bottom moulding at the front screen is attached. It obviously needs clips but what do they look like and where do they fit.
...
Forum: Pontiac - Street 12-15-2011, 11:52 PM
Replies: 6
Views: 461
Posted By ironman
Engine will not turn off

Recently fired the engine in my 68 fire bird and all was fine except the alternator was not charging. Sorted that out, the field wire on the alternator was open circuit. Alternator now charges and...
Forum: Electrical Tech 12-15-2011, 11:51 PM
Replies: 4
Views: 535
Posted By ironman
engine will not turn off

Recently fired the engine in my 68 fire bird and all was fine except the alternator was not charging. Sorted that out, the field wire on the alternator was open circuit. Alternator now charges and...
Forum: Pontiac - Street 10-06-2011, 11:13 PM
Replies: 2
Views: 302
Posted By ironman
TH350 vacuum modulator

Can anybody tell me where I need to hook this up, ported or unported vacuum.

Thanks
Forum: Pontiac - Street 09-06-2011, 09:04 PM
Replies: 1
Views: 438
Posted By ironman
starter motor

Are the noses on pontiac and chev starters interchangeable,can i put the nose from my pontiac starter on a chev starter without any other mods.

Thanks
Forum: Pontiac - Street 07-04-2011, 02:34 AM
Replies: 0
Views: 481
Posted By ironman
Universal joints

Guys,
Having some difficulty in Australia:oogle: obtaining the correct universal joints for my 68 firebird. Has a turbo 350 and standard 8.2 inch BOP rear axle. Are Spicer 5-811X the right...
Forum: Pontiac - Street 04-25-2011, 04:41 AM
Replies: 2
Views: 686
Posted By ironman
Bearing interchange

I need to fit new rod bearings to my 400 and can pick up a set of 301 rod bearings for nothing. Are they the same and can I use them on my 400.

Thanks:confused:
Forum: Pontiac - Street 09-06-2010, 10:59 PM
Replies: 2
Views: 453
Posted By ironman
modified stock iron manifold

I have modified my stock manifold and have removed the crossover section. I will need plates to block off this area on the head intake face, not sure of the size im thinking 2" wide and 1/2" thick...
Forum: Pontiac - Street 08-28-2010, 05:59 AM
Replies: 4
Views: 713
Posted By ironman
Rocker studs

Looking at replacing my standard bottle neck studs on a set of 6x heads, will be using stock stamped rockers and there seems to be quite a number of 7/16 studs available. Im thinkink the ARp 100-7101...
Forum: Pontiac - Street 08-19-2010, 10:27 PM
Replies: 8
Views: 988
Posted By ironman
rebuilding heads

Just got my heads back from the machinist, one of the things i had done was have the guides machined for positive type seals, is there a recomended way to install the seals on the guides also I have...
Showing results 1 to 25 of 61
Page 1 of 3 1 23

 
Forum Jump

All times are GMT -4. The time now is 09:11 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017